WB Mfg iXchange SSW1202-AL Скачать руководство пользователя страница 15

wibenchmfg.com

507 E. Grant St. Thorp, WI 54771 • P - 800.242.2303

Specifications are subject to change. Product 

images are for illustrative purposes only and may 

differ from the actual product.

15

iXchange® Wall

Assembly Instructions

SSW1202-AL

Care & Maintenance

Storage Cabinet Surfaces

Daily Care and Cleaning for Laminate Surfaces

The laminate surface may be cleaned with warm water and 

mild soaps, such as those used for hands or dishes.  Heavy 

solvents can affect edging adhesion.
Note, that while there are different grades and chemical 

resistance properties to various types and manufacturers of 

plastic laminate, the cleaning recommendations are universal.
To clean the surface, use a damp cloth or sponge and a mild 

soap or detergent. Difficult stains such as coffee or tea can 

be removed using a mild household cleaner and baking soda; 

mixing to achieve a paste consistency. Use a stiff nylon bristle 

brush, scrubbing (approx. 15-20 strokes) the affected area. Do 

not scrub so as to damage or scratch the surface finish. Doing 

so will void the warranty.
Stubborn stains that resist any of the above cleaning methods 

may require the use of undiluted household bleach or nail 

polish remover. Use a cotton ball saturated with bleach or nail 

polish remover (acetone); gently rub the stain for up to two 

minutes. Rinse thoroughly with warm water and wipe dry using 

a soft cloth. This step may be repeated if the stain appears to 

be going away and the color of the laminate has not 

been affected.

WARNING: 

Prolonged exposure of the laminate surface to 

bleach will cause discoloration. Always rinse laminate surfaces 

after cleaning! Failure to rinse after cleaning can cause 

damage; even if a small amount of cleaning solution remains 

on the surface. A dry residue may be invisible; however, 

moisture from cups or drinks can reactivate it, and result in 

permanently etched scars or stains over time.

Recommended Household Cleaners:

•  Clorox® (Prolonged exposure can mar the surface)
•  Formula 409®
• Dawn®
•  Glass Plus®
•  Dow Bathroom Cleaner with Scrubbing Bubbles™
• Fantastik®
• Favor®
• Windex
• Lestoil®
• Pledge®

•  Grease Relief®
•  Mr. Clean®
•  Lysol® Brand Disinfectant Basin/Tub/Tile Cleaner
•  TOP JOB®

A Few Notes of Caution:

Acidic or abrasive cleaners can damage laminate surfaces; do 

not use them.  Drain cleaners containing lye will permanently 

damage the laminate surface. If you spill a drain cleaner, wipe 

it up immediately and rinse several times with water.
Hair, textile and food dyes can cause permanent stains. If 

dye should happen to spill, wipe it up immediately with dish 

washing detergent or an all-purpose cleaner.
•  Wipe spills away promptly and rinse several times with water.
•  Rust removers contain harsh chemicals, which will quickly 

cause permanent damage. If a spill occurs, wipe off residue 

immediately and wash thoroughly with soapy water and rinse  

several times.
•  Steel wool and other abrasive pads will damage the laminate 

face. Do not use them for cleaning and don’t store steel wool 

pads on your counter top; the metal can rust and leave stains.
•  Toilet bowl cleaners contain harsh chemicals that can cause 

permanent damage.
•  If spills occur, wipe up immediately, wash surface with soapy 

water and rinse several times.
•  Sharp objects can damage the surface; marring its beauty 

and lowering wear and stain resistance. Although high 

pressure laminates are somewhat resistant to scratch and 

marring, the surface can be damaged, even under normal use.
•  Laminate surfaces may need occasional dusting depending 

on where it’s used.
•  To keep the surface beautiful, use a non-oily furniture 

spray. Furniture polish can also help hide fine scratches in the 

surface.
•  Excessive contact with moisture, high humidity and other 

harsh environmental conditions may not affect the laminate 

surface itself, but may cause the laminate surface to pull away 

from the core material it is adhered to, causing failure.
•  Although not a material failure, this is considered a product 

failure and may void the product warranty.
The cleaners listed below can cause damage to the surface of 

laminate:

Chemical Ingredient Synonymous Names

Hydrochloric Acid

Muriatic Acid, Hydrogen Chloride

Sulfuric Acid

Oleic Acid, Oil of Vitriol, Oleum

Hydrofluoric Acid

Rust Remover

Phosphoric Acid

Rust Remover

Sodium Hydroxide

Caustic Soda, Caustic Lye, Soda Lye

Содержание iXchange SSW1202-AL

















Отзывы: