Waygate Technologies Krautkramer USM 100 Скачать руководство пользователя страница 159

Страница: 159 / 330

Evaluation

5 Operation

Krautkrämer USM 100

Rev. 9 (09/2023)

159

Eval Mode

You must choose the evaluation mode before setting
the following parameters.

dbRef Mode

This parameter is only visible when

dB REF

has been

selected in

Eval Mode

You can switch the evaluation method on or off.

Gate A Start

This is the same function as in the function group

Gates

(see page 146).

Eval Source

This parameter is only visible when

DAC

JISDAC

CNDAC

has been selected in

Eval Mode

You can choose between the A-scan and the envelope
curve as basis for the evaluation.

Eval Points Source

This parameter is only visible when

DAC

JISDAC

CNDAC

has been selected in

Eval Mode

For creating and editing the DAC curve points you have
two options:

●

DAC Table

: The DAC table is defined with the soft-

ware

Mentor Create.

●

Custom

: You can record the DAC points with the in-

strument.

The software

Mentor Create

is described in a separate

manual.

Define Points

This parameter is only visible when

DAC

JISDAC

CNDAC

has been selected in

Eval Mode

You can set the number of points to be recorded.

Содержание Krautkramer USM 100










































































































































































































































































































































Результаты поиска

Содержание Krautkramer USM 100

Отзывы:

Waygate Technologies Krautkramer USM 100, Руководство по эксплуатации, Страница: 159 / 330

Результаты поиска

Содержание Krautkramer USM 100

Отзывы: