Waygate Technologies Krautkramer USM 100 Скачать руководство пользователя страница 141 | Manualshive

Страница: 141 / 330

Waygate Technologies Krautkramer USM 100 Скачать руководство пользователя страница 141

UT Setup

5 Operation

Krautkrämer USM 100

Rev. 9 (09/2023)

141

5.12 UT Setup

In this function group you will find the settings for gain
control, alarms and output signals.

Gain

is only visible when

is set to

On

.

This is the same function as in the function group

(see page 122).

AGC Mode

Even smaller variations of the echo amplitude can lead
to incorrect measurement results in wall thickness mea-
surements. In these cases, the exact monitoring of the
amplitude is therefore highly important. The automatic
gain control (AGC) offers practical help for this purpose.

The automatic gain control of the USM 100 keeps the
echo amplitude fully automatically at a specified screen
height and, in this way, compensates for the amplitude
variations of the signal received. This enables to clearly
improve especially the wall thickness measurement and
to make it easier.

The AGC can also be used during calibration in order to
keep the reference amplitude of 80 % screen height
constant at ±1 % (setting

AGC Max Amp

= 81 %,

AGC

Min Amp

= 79 %).

«
...
139
140
141
142
143
...
»

Содержание Krautkramer USM 100











































































































































































































































































































































Отзывы:

Нет отзывов