Waygate Technologies Krautkramer USM 100 Скачать руководство пользователя страница 138 | Manualshive

Страница: 138 / 330

Waygate Technologies Krautkramer USM 100 Скачать руководство пользователя страница 138

5 Operation

Pulser Receiver

138

Rev. 9 (09/2023)

Krautkrämer USM 100

Upper Freq

The function

is only visible if the setting

Adjustable

is selected in the

function.

Set the low cutoff frequency for the filter range here.
Frequencies below this cutoff frequency are blocked.

Damping

This function is used for matching the probe. By setting
the damping level of the probe oscillating circuit you can
vary the height, width, and resolution of the echo dis-
play.

400 Ohms

This setting gives a low damping, the echoes become
higher and broader.

50 Ohms

This setting reduces the echo height but produces nar-
rower echoes with a higher resolution.

Dual Mode

You can toggle between single-element and dual mode.

Off

This setting is for single-element operation. The probe
must be connected to the

T/R

socket (see page 53).

On

The dual mode is for using dual-element probes. The re-
ceiver must be connected to the

R

socket and the pulser

to the

T/R

socket (see page 53).

«
...
136
137
138
139
140
...
»

Содержание Krautkramer USM 100











































































































































































































































































































































Отзывы:

Нет отзывов