manualshive.com logo in svg

Wavespan Stratum 100, Руководство по установке и обслуживанию

Поделиться
Скачать
Wavespan Stratum 100 Скачать руководство пользователя страница 49

Stratum 100 Installation and Maintenance Guide

Maintaining and Monitoring the Stratum 100  

••

  41

---------------------------- RF Packet Intervals -----------------------------

 System Status: STBY - NOT CONNECTED - ALARM            [ Alarms & Events.. ]

         Local: Current Interval 04:45       Remote: Current Interval 04:45
         ---------------------------------   ----------------------------------
           TxPkt       RxPkt      Brdcast      TxPkt       RxPkt      Brdcast
 00:00           0           0           0            ?           ?           ?
 00:15           0           0           0            ?           ?           ?
 00:30           0           0           0            ?           ?           ?
 00:45           0           0           0            ?           ?           ?
 01:00           0           0           0            ?           ?           ?
 01:15           0           0           0            ?           ?           ?
 01:30           0           0           0            ?           ?           ?
 01:45           0           0           0            ?           ?           ?
 02:00           0           0           0            ?           ?           ?
 02:15           0           0           0            ?           ?           ?
 02:30           0           0           0            ?           ?           ?
 02:45           0           0           0            ?           ?           ?
 03:00           0           0           0            ?           ?           ?
 03:15           0           0           0            ?           ?           ?
-------------------------------------------------------------------------------
 [ Page Up ] [ Page Down ] [ Home ] [ End ]             [ ^Update ] [ ^Cancel ]
-------------------------------------------------------------------------------

Choosing 

RF Error Interval 

will display a screen that shows error intervals. <<??>>

-------------------------------- Error Intervals -----------------------------

 System Status: STBY - NOT CONNECTED - ALARM            [ Alarms & Events.. ]

        Local: Current Interval 04:45       Remote: Current Interval 04:45
        ---------------------------------   ----------------------------------
        RxCorrpt           RxOvruns         RxCorrpt           RxOvruns
 00:00         0                  0                  ?                  ?
 00:15         0                  0                  ?                  ?
 00:30         0                  0                  ?                  ?
 00:45         0                  0                  ?                  ?
 01:00         0                  0                  ?                  ?
 01:15         0                  0                  ?                  ?
 01:30         0                  0                  ?                  ?
 01:45         0                  0                  ?                  ?
 02:00         0                  0                  ?                  ?
 02:15         0                  0                  ?                  ?
 02:30         0                  0                  ?                  ?
 02:45         0                  0                  ?                  ?
 03:00         0                  0                  ?                  ?
 03:15         0                  0                  ?                  ?
-------------------------------------------------------------------------------
 [ Page Up ] [ Page Down ] [ Home ] [ End ]             [ ^Update ] [ ^Cancel ]
-------------------------------------------------------------------------------

Use the down arrow to move to 

Cancel 

and press Enter to leave this report screen.

Checking that Packets are Being Bridged to/from the
Ethernet Link

From the Reports Menu, use the down arrow to go to 

LAN Status 

and press Enter to display

that report.

Содержание Stratum 100




































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды