Wavelength Electronics WTC3293, Техническое описание и руководство по эксплуатации

Страница: 8 / 36

© 2022 www.teamWavelength.com 8
WTC3243 TEMPERATURE CONTROLLER
ELECTRICAL SPECIFICATIONS — WTC3243
ABSOLUTE MAXIMUM RATINGS SYMBOL WTC3243 WTC3243HB UNIT NOTE
Supply Voltage 1 V
DD
+4.5 to +30 +3 to +5.5 Volts DC
Voltage on Pin 1
Can be connected to V
S
Consult SOA Calculator
Supply Voltage 2 V
S
+3 to +30 +3 to +8 Volts DC
Voltage on Pin 14
Can be connected to V
DD
Consult SOA Calculator
Power Dissipation P
MAX
9 Watts
T
AMBIENT
= +25ºC
See SOA Chart -- with fan
and heatsink
Case Operating Temperature T
OPR
-40 to +85 ºC
Case Storage Temperature T
STG
-65 to 150 ºC
PARAMETER SYMBOL WTC3243 WTC3243HB UNIT NOTE
OUTPUT CURRENT
Maximum Output Current I
OUT
±2.0 to ±2.2 ±2.2 Amps
Compliance Voltage, OUTA to OUTB V
S
- 0.1 Volts
Full temp. range,
I
OUT
= 100 mA
Compliance Voltage, OUTA to OUTB V
S
- 0.3 Volts
Full temp. range,
I
OUT
= 1 A
Compliance Voltage, OUTA to OUTB V
S
- 0.6 Volts
Full temp. range,
I
OUT
= 1.5 A
Compliance Voltage, OUTA to OUTB V
S
- 0.9 Volts
Full temp. range,
I
OUT
= 2.0 A
Compliance Voltage, Resistive Heater V
S
- 1.0 Volts
Full temp. range,
I
OUT
= 2.2 A
Short Term Stability (1 hour) 0.0009 ºC
OFF ambient temperature
TSET = 25ºC using 10 kΩ
thermistor
(1)
Short Term Stability (1 hour) 0.002 ºC
ON ambient temperature
TSET = 25ºC using 10 kΩ
thermistor
(1)
Long Term Stability (24 hours) 0.002 ºC
OFF ambient temperature
TSET = 25ºC using 10 kΩ
thermistor
(1)
POWER SUPPLY
Power Supply Voltage
V
DD
= +4.5 to +30
V
S
= +3 to +30
V
DD
= +3 to +5.5
V
S
= +3 to +8
Volts
Quiescent Current
V
DD-QUIESCENT
= 8
V
S-QUIESCENT
= 2.5
mA
Minimum Current Rating
V
DD
= 1.1 * V
DD-QUIESCENT
V
S
= 1.1 *(I
TEC
+ V
S-QUIESCENT
)
Amps
TEMPERATURE SENSORS
Sensor Compatibility Thermistors, RTD, IC Sensors
Sensor Input Voltage Range GND to V
DD
- 2 Volts
Limited by bias current
circuit
(2)
Sensor Input Damage Threshold > V
DD
+ 0.7 or < -0.7 Volts
Without the bias current
circuit
(1)
When using resistive heaters, stability can only be consistently achieved when specified temperatures are 10°C or more above ambient.
(2)
The bias source has a compliance up to V
DD
- 2 V. In normal operation this limits the sensor voltage range from 0 V to V
DD
- 2 V. While
voltages up to ±5 V outside this range on the VSET pin will not damage the unit, it will not provide proper control under these conditions.