Wavecom W-CLOUD Скачать руководство пользователя страница 250 | Manualshive

Страница: 250 / 381

background image

240



Transmission Modes

WAVECOM Decoder W74PC, W-PCI/e, W-CODE, W-CLOUD Manual V9.1.0

With the help of the FFT-Analysis-Tool look for a SAT-MINI-M-HSD signal (bandwidth 40 kHz, QAM16 33.6
kSymbol/sec) with a lot of traffic.

In the

Satellite

mode menu choose

Inmarsat

,

SAT-MINI-M-C-HSD

.

The Session Window displays the start and end of a session. The “MES_ID” displayed is the return MESId
of the MES (Mobile Earth Station); the “Frequency” is a dummy value.

The Session List Window displays the results of the successfully decoded sessions. The decoded data is
saved as “Hsd.txt”.

Additional information

:

See “

SAT Settings…

” on page 44.

See “

” on page 298.

SI-ARQ

SI-ARQ is a simplex system similar to for example SITOR. SI-ARQ therefore also sounds similar to the
well-known SITOR system. Because data and pause blocks are longer in duration, the perception of a low-
er baud rate is created.

Parameter

Value

Frequency range

HF

Operation modes

Simplex ARQ

Modulation

FSK

Symbol rate

96.0, 192.0 and 200.0 Bd

Receiver settings

DATA, CW, LSB or USB

Input format(s)

AF, IF

Additional Info

ITA-3

SI-ARQ operates at symbol rates of 96, 192 or 200 Bd on the radio link.

SI-ARQ uses the ITA-3 alphabet for data transmission and error detection. Data blocks usually consist of 5
or 6 characters.

One transmission cycle is made up of twice the length of a character block. If the information sending sta-
tion (ISS) receives an acknowledgement character, the next data block is sent with inverted phase or po-
larity. However, if the receiving station (IRS) requests a retransmission, the repeated block is sent with
unchanged polarity.

If the ISS does not receive the acknowledgement packet, it transmits a RQ block as is the case with SI-
TOR.

The software automatically detects SI-ARQ block lengths of four, five or six characters and displays this
information after phasing has been achieved. The polarity of the signal is automatically detected.

Transmission Sequence of SI-ARQ at 96 Baud with Five Characters

SI-AUTO

Fully automatic tuning to signal center, shift and transmission modes SI-ARQ (Mode A) and SI-FEC (Mode
B) may be achieved by selecting

SI-AUTO

mode.

«
...
248
249
250
251
252
...
»

Содержание W-CLOUD






























































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для W-CLOUD

Бренд: Galaxy Audio Страницы: 6

Бренд: Vanner Страницы: 44

Бренд: Coleman Страницы: 12

Бренд: Sungrow Страницы: 14

Бренд: Senergy Страницы: 50

Бренд: SAJ Страницы: 26

Бренд: Lika Страницы: 2

Бренд: FireBird Страницы: 44

Бренд: Teracue Страницы: 68

Бренд: Samlexpower Страницы: 56

SO SPEAKY HDMI+ SK5

Бренд: DANE-ELEC Страницы: 16

Бренд: Hall Research Technologies Страницы: 8

Бренд: Sinexcel Страницы: 49

Бренд: Manhattan Страницы: 2

Бренд: Nightlife Страницы: 12

Бренд: BZB Gear Страницы: 22

Бренд: ICP DAS USA Страницы: 2

Бренд: X-Micro Страницы: 84

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды