Watts WM-120-PT Скачать руководство пользователя страница 5

 

5

e)  Tighten bottom clamp evenly. (Brackets 

should be p arallel). 

f) 

Turn handle clockwise to close the valve. 

g)  Connect ¼” green tubing from the unit to 

the Self-Piercing Valve as shown in figure 
C. Failure to do this before piercing the tube 
will cause a small amount of water to escape 
from the outlet. 

h)  Turn on water supply and open the tapping 

valve by turning the handle counter 
clockwise.  

i) 

Check for leaks and repair if any.

 

 

Figure C  

 
 
 
 
 
 
 
 
 
 
 
 

Processor B 

Installing Easy Tap Adapter 

Cold Water Supply Only 

 

Easy tap adapter to be installed on ½” male pipe 
thread connection before angle stop valve or onto 
the faucet. Note: If your plumbing does not 
allow for connection of easy tap adapter contact 
your local plumbing or hardware store for 
modifications.  

(a) 

Turn off the supply water. The Easy 
Tap Adapter may be installed before 
angle stop valve (as shown in figure 
C1), or installed at the faucet (as 
shown in figure C2).

 

Note: Plumbing connections maybe reversed 
from drawing below. 

 
Figure C1 

 

 
 
 
 
 
 

 
 

 
 
 
 
 

Figure C2 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
(b)  Teflon tape the 1/8” male pipe thread of the 

easy tap valve and screw into easy tap valve 
body. 

(c)  Disconnect the fitting where the easy tap 

valve is to be installed. 

Note: When 

loosening or tightening fitting use 
wrenches on both sides of fittings.   

 

(d)  Insert the easy tap gasket into the female 

thread side of easy tap. No plumber putty or 
Teflon tape is required on thread. 

(e)  Thread easy tap valve on to the ½” male 

pipe threads and tighten securely with 
wrenches

. Note: Use wrenches on both 

sides of the connections.

  

(f)  Thread angle stop valve or plumbing line to 

the other end of the  easy adapter valve and 
tighten securely using wrenches. 

(g)  Connect green tubing from unit to the easy 

tap valve (as shown in figure C1 or C2). 

(h)  Turn handle clockwise making sure that 

easy tap valve is in the closed position. 

 

Brass nut

Delrin Sleeve 

Brass Insert

Valve Handle

3/8” cold water line

1/4” green tubing

Lance

Rubber Gasket

For water line sizes greater than 3/8”

Sink faucet

Gasket

Easy Tap
Valve

1/2” connection
plumbing from
angle stop

Brass insert

Delrin sleeve

Brass Nut

Tubing

Gaske

Easy 

Tap 

Angle

Stop 

Nut

Tubin

Delrin  
Sleeve

Brass
insert

Plumbing 
connection
sink faucet

Содержание WM-120-PT









Отзывы: