background image

Watts TK-DL Software Instructions

The Watts TKDLC102 Software Disc is menu driven and will prompt you throughout the process of down loading your Watts 
TK-DL test results to a personal computer.  The following information has been provided to assist you in utilizing your Watts 
TK-DL test kit.

TK DLC 102: Enter

READ WRITE TO TESTER: Enter

Connect TK-DL to computer and turn on 
(on screen instructions)

A.

  Load Data from Tester

 

 

Reads Tester information in memory.

B.

 Display 

settings

 

 

Model = Watts TK-DL

  Eprom 

Version

  Serial 

#

  Time/Date
  Last 

Calibrated

  Next 

Cal 

Due

  Next 

Test 

#

C.

 Change 

Settings

 

 

Time/Date - day only

D.

  Display Heading and Footer

 

 

Displays heading and footer in TK-DL

 

 

memory printed on tape.

E.

  Change Heading and Footer

 

 

Allows heading and footer to be changed

 

 

by using computer keyboard.

F.

 

Write Data to Tester (Saves information to the 

 

Test Kit once you have changed the header or 

 

the footer or anything in the “Change Settings” 

 option).

G.

  Load Heading File

 

 

It recalls a heading that was previously 

 

 

saved.  You can then load into the TK-DL 

 

 

when you are connected to the computer.  

 

 

After loading you must write data to tester 

  (Step 

F).

H.

  Load Footing File

 

 

Same as load heading, except for footer.

G., H.

 Brings up headers and footers that were pro-

 

grammed and saved at an earlier time.  You may 

 

recall the footer or header to program into you test 

 

kit.  The recalled or “Loaded” information will 

 

overwrite current information.

I.

 Save 

Heading

J.

 Save 

Footing

I, J,

 Use this option when you have changed the header 

 

or the footer and want to save the changes.  You 

 

can save each header and footer in a separate fi le.  

 

You can then recall or “Load” the header or footer to 

 

be programmed into your test kit.

K.

  Down Load Tests

 

 

Down loads from TK-DL to disc.

L.

 Print 

Tests

  On 

screen 

prompts:

 

 

 

F2 OK, F4 scroll up, F6 scroll on,

   Esc 

to 

cancel.

 

 

 

Lists date and Time tests

   were 

recorded.

 

 

 

     to select test to print

 

Note:

 The disc included with your test kit allows you 

 

to change your header or footer.  Therefore, the disc 

 

should not be carried in the test kit case.

 

 

 

IS-TK-DL   0829 

EDP# 1910763

 

© Watts, 2008 

USA:

  815 Chestnut St., No. Andover, MA 01845-6098; www.watts.com

Canada:

  5435 North Service Rd., Burlington, ONT. L7L 5H7; www.wattscanada.ca

B a c k f l o w   P r e v e n t i o n   P r o d u c t s

IS-TK-DL.indd   8

9/5/08   2:18:59 PM

Содержание TK-DL









Отзывы: