12 PWSR Series Softeners
Press the
Set Clock
button
Adjust hours using the
Up
and
Down
arrow buttons
Press the
Next
button to advance
to the minutes .
Adjust minutes with the
Up
and
Down
arrow buttons .
Press the
Next
button to set time
To Exit
Chart 1: Setting Time of Day
The
Water Hardness
level of the feed water needs to be known prior to programming system as well as the
Water Softener Capacity
of the
system being installed, to insure proper programming and efficiency of system
NOTICE
Once in the programming settings, simply use the
UP
and
DOWN
arrow buttons to change values
NOTICE
To enter the Master Programming
mode, press and hold the
NEXT
and
DOWN
arrow buttons simulta-
neously for 3 – 5 seconds
The display will change to
SET SOFTENING
with the word
SOFTENING
will be blinking .
This indicates you are now in the Master Programming Mode
System Type – For a
WATER SOFTENER
, leave this setting alone . If for some reason the
display reads
SET FILTER
, press the
UP
arrow button and change to
SET
SOFTENER
Press
NEXT
Button
Capacity – Enter the
CAPACITY
of the water softener that you have ie .
30K, 45K, 60K or
90K.
Press
NEXT
Button
Salt Setting – Enter the desired pounds of salt per regeneration ie . 6 lbs . per cu .ft . of resin for
most efficiency, 15 lbs . per cu .ft . for maximum capacity – default setting should be
9
pounds
for a 45K water softener – you must confirm
Press
NEXT
Button
A 30K water softener has 1 cu .ft ., 45K has 1 .5 cu .ft ., 60K has 2 cu .ft . and 90K cu .ft . has 3
cu .ft . Example - 45K water softener would be set to a minimum salt setting of 9 pounds for
most efficiency (recommended)
Press
NEXT
Button
Backwashing Mode - Setting to Normal or Longer .
NORMAL
is the standard setting . Longer
may be needed for well water with heavier sediment issues . Contact Pure Water Technical
Support at
1.800.224.1299, then press #2
for details .
Press
NEXT
Button
Gallon Capacity Mode - Set to
AUTO
for most efficient setting . Owner’s manual has addi-
tional settings, contact Pure Water Technical Support for Details . Note: You may see a gallon
capacity on this screen, hit the
UP
arrow button several times until you see
AUTO
on the
screen .
Press
NEXT
Button
Brine Tank Refill Mode - This setting should be set to
POST
Press
NEXT
Button
Regenerate Flow Mode - This flow setting should be set to Down Flow –
dn
.
Press
NEXT
Button
Regeneration Time - This setting should be set to
NORMAL
Press
NEXT
Button
This will complete Master Programming Steps
Chart 2: Master Programming
To enter Installation Display Setting
Programming mode, press and hold
the
NEXT
and
UP
arrow buttons
simultaneously for 3 - 5 seconds
Hardness Setting - Set the level of hardness in grains per gallon (GPG) present in the raw
water . Example:
18
grains per gallon (GPG) . Adjust grains per gallon with the
Up
and
Down
arrow buttons .
Press
Next
Button
Day Override . Default should be set to
14
Days . Watts Pure Water water softeners regener-
ate based on water usage, but this day override setting will come into play if the softener sits
idle or has not regenerated and will automatic initiate regeneration on the 14th day .
Press
Next
Button
Regeneration Time . Default setting is
2:00 AM
. If time change is needed, press the
UP
and
DOWN
arrow buttons to adjust the hour time .
Press
Next
Button
Press the
UP
and
DOWN
arrow button to adjust the minutes .
Press
Next
Button
Chart 3: Installer Programming
Next you will need to set up Installer Programming, this
MUST
be done in addition to the Master Programming
NOTICE
Programming completed, Valve will return to normal mode and will be in service.
If you have additional questions regarding your water softener programming, please contact
Pure Water Technical Support at 1.800.224.1299, then press #2
Содержание PWSR Series
Страница 27: ...NOTES ...
