background image

25

SXT Controller Programming and Operation 

Features of the SXT:

•  Power backup that continues to keep time and the passage of 

days for a minimum of 48 hours in the event of power failure. 

During a power outage, the control goes into a power-saving 

mode. It does not monitor water usage during a power failure, 

but it does store the volume remaining at the time of power 

failure.

•  Settings for both valve (basic system) and control type (method 

used to trigger a regeneration).

•  Day-of-the-Week controls. 
•  While in service, the display alternates between time of day, 

volume remaining or days to regeneration, and tank in service 

(twin tank systems only).

•  The Flow Indicator flashes when outlet flow is detected.
•  The Service Icon flashes if a regeneration cycle has been 

queued.

•  A Regeneration can be triggered immediately by pressing the 

Extra Cycle button for five seconds.

•  The Parameter Display displays the current Cycle Step (BW, BF, 

RR, etc) during regeneration, and the data display counts down 

the time remaining for that cycle step. While the valve is trans-

ferring to a new cycle step, the display will flash. The parameter 

display will identify the destination cycle step (BW, BF, RR, etc) 

and the data display will read “----”. Once the valve reaches the 

cycle step, the display will stop flashing and the data display 

will change to the time remaining. During regeneration, the user 

can force the control to advance to the next cycle step immediately 

by pressing the extra cycle button.

Setting the Time of Day

1.  Press and hold either the Up or Down buttons until the pro-

gramming icon replaces the service icon and the parameter 

display reads TD.

2.  Adjust the displayed time with the Up and Down buttons.
3.  When the desired time is set, press the Extra Cycle button to 

resume normal operation. The unit will also return to normal 

operation after 5 seconds if no buttons are pressed.

Manually Initiating a Regeneration

1.  Press the Extra Cycle button. The service icon will flash to  

indicate that a regeneration is queued.

2.  To cancel a queued regeneration, press the Extra Cycle button.

Regenerating Immediately

Press and hold the Extra Cycle button for five seconds.

42637 Rev D

Error/ 

Information Icon

Service  

Icon

Parameter 

Display

Data 

Display

PM

Indicator

Programming 

Icon

x1000 Indicator

Extra Cycle 

Button

Up 

Button

Down 

Button

Flow Indicator

Figure 1

Controller Display

Содержание PWS15 Series

























































Отзывы: