background image

STEP 6

When the required level is reached, or if the tank is overflowing, 
SLOWLY turn the adjustment screw OUT, counterclockwise, in ¼ 
to ½ turn increments (See Figure 4). A small amount of water will 
discharge from the vent/exhaust line of the Altitude control, signal-
ing the port connection changes of both the Altitude Control and 
accelerator. The valve will start closing as indicated by the position 
indicator stem movement.

The following is dependent upon the installation/application and 
may not be required on all valves: When the valve is closed, the 
Altitude control screw adjustment may be turned OUT, counter-
clockwise, an additional ¼ to ½ turn (See Figure 4). This will lower 
the shut-off level slightly below the tank over-flow mark, eliminat-
ing any wave action discharge from the over-flow pipe. 

Setting the Altitude Pilot 

STEP 4

Slowly open the downstream isolation valve.

STEP 5

If the valve remains closed as indicated by the stem position in 
the position indicator (See Figure 2) and the tank level is known 
to be below the desired level, SLOWLY turn the adjustment screw 
IN, clockwise, by ¼ to ½ turn increments (See Figure 3).

This will cause the valve to start opening, filling the tank. 
Additional clockwise adjustment may be necessary to raise the 
level to the overflow line.

4          IOM-ACV-127-3_6127-3 2115 

EDP# 1917067 

© 2021 Watts

IOM-ACV-127-3_6127-3 2115 

EDP# 1917067 

© 2021 Watts         5

Clockwise to INCREASE 

minimum tank level set 

point.

Figure 3 

Model 27 - Altitude Pilot

Counterclockwise to DECREASE 

minimum tank level set point.

Figure 4 

Model 27 - Altitude Pilot

Figure 2 

Position Indicator Stem in Down Position 

Indicating Valve Closed

Содержание LFM127-3













Отзывы: