background image

Troubleshooting 

PROBLEM 

CAUSE 

SOLUTION 

Check value fails to hold 1.0 psid minimum  Debris on sealing surface, guide surfaces, or valve surfaces  Disassemble and clean check 

Damaged seat disc 

Disassemble and replace seal 

Weak or broken spring 

Disassemble and replace spring 

Poppet broken due to thermal expansion 

Replace broken poppet (Refer to IS-F-765-Winterization at watts.com.) 

Poppet fails to open at 1.0 psig minimum 

Debris restricting free operation 

Disassemble and clean check valve surfaces 

Poppet seal adhering to bonnet 

Disassemble and clean and/or replace damaged parts 

Weak spring load 

Replace bonnet assembly (½" to 1¼") 

Replace spring (1½" and larger) 

Minor leakage through air vent 

Damaged poppet seal 

Disassemble and replace seal 

Cracked or damaged poppet 

Disassemble and replace poppet seal 

Cracked bonnet or damaged sealing edge 

Disassemble and replace bonnet assembly 

Debris on sealing surface 

Disassemble and clean 

Significant discharge through air vent 

Poppet not properly guided 

Disassemble and replace damaged parts 

Major poppet or seal failure 
Low downstream pressure 

Check pressure at test cock No. 2; should be higher than 5 psig if low system 

Insufficient inlet volume to operate device 

Increase pressure or partially close outlet ball valve to create higher pressure 

on poppet 

Poppet and or bonnet broken due to thermal expansion 

Replace broken bonnet/poppet (Refer to IS-F-765-Winterization at watts.com.) 

Chatter during flow conditions 

Worn, damaged, or defective check valve guide 

Disassemble and repair or replace guide 

Add-on/Retrofit Sensor Connection Kit 

ORDERING CODE  ADD-ON/RETROFIT KIT 

DESCRIPTION 

88009430 

FP-FBF-BMS/IMS-FZ 

BMS/IMS Freeze Sensor Connection Kit 

Includes freeze sensor in mounting clip, activation module with mounting 

hardware, wire nuts (2), and power adapter. Use this kit to add an indicator 

of the freeze threshold for PVB assemblies in a BMS/IMS configuration. 

Limited Warranty:

 FEBCO (the “Company”) warrants each product to be free from defects in material and workmanship under normal usage for a period of one year from the date of original shipment. 

In the event of such defects within the warranty period, the Company will, at its option, replace or recondition the product without charge. 

THE WARRANTY SET FORTH HEREIN IS GIVEN EXPRESSLY AND IS THE ONLY WARRANTY GIVEN BY THE COMPANY WITH RESPECT TO THE PRODUCT.  THE COMPANY MAKES NO OTHER 

WARRANTIES, EXPRESS OR IMPLIED.  THE COMPANY HEREBY SPECIFICALLY DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED 

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. 

The remedy described in the first paragraph of this warranty shall constitute the sole and exclusive remedy for breach of warranty, and the Company shall not be responsible for any incidental, special 

or consequential damages, including without limitation, lost profits or the cost of repairing or replacing other property which is damaged if this product does not work properly, other costs resulting from 

labor charges, delays, vandalism, negligence, fouling caused by foreign material, damage from adverse water conditions, chemical, or any other circumstances over which the Company has no control. 

This warranty shall be invalidated by any abuse, misuse, misapplication, improper installation or improper maintenance or alteration of the product. 
Some States do not allow limitations on how long an implied warranty lasts, and some States do not allow the exclusion or limitation of incidental or consequential damages.  Therefore the above 

limitations may not apply to you.  This Limited Warranty gives you specific legal rights, and you may have other rights that vary from State to State.  You should consult applicable state laws to 

determine your rights. 

SO FAR AS IS CONSISTENT WITH APPLICABLE STATE LAW, ANY IMPLIED WARRANTIES THAT MAY NOT BE DISCLAIMED, INCLUDING THE IMPLIED WARRANTIES OF 

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO ONE YEAR FROM THE DATE OF ORIGINAL SHIPMENT. 

USA:

 T: (800) 767-1234 • 

 • 

 • 

FEBCOonline.com 

Canada: 

T: (888) 208-8927 FEBCOonline.ca 

Latin America: 

T: (52) 55-4122-0138 FEBCOonline.com 

RP/IS-F-FZ-765  2332 

1923078 

© 2023 Watts 

Содержание FEBCO 765



















Отзывы: