Watts AERCO SmartPlate SP150 Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 134

background image

SmartPlate Installation, Operation & Maintenance Manual

CHAPTER 4

– ADJUSTMENT

OMM-0069_0H

• SP-100 • 1/30/2020 Technical Support • (800) 526-0288 • Mon-Fri, 8 am - 5 pm EST Page

29

of

134

CONTROL VALVE CALIBRATION

Instructions

4. Set the ECS/SP Control Box POWER switch to the ON position to apply 24 VAC power to

the Control Valve Actuator (pins 1 (G0) and 2 (G). Ensure the Valve is in the AUTO
position, the LED indicator will light green continuously indicating that Valve operation is
normal (no faults).

5. Using a pin or paper clip, depress the auto-stroke button in the opening of the terminal

housing (Figure 4-2). This will initiate calibration of the Control Valve.

6. During actuator calibration, the LED indicator (Figure 4-2) will flash green for approximately

10 seconds. The Control Valve will be briefly closed and fully opened.

7. Upon successful completion of the Valve calibration process, the LED indicator will stop

flashing and remain ON continuously green.

8. The two-color (Red/Green) indicator is useful in determining the operating status of the

Control Valve. Refer to Table 4-1 for descriptions of the possible LED status displays which
may be encountered.

TABLE 4-1. Control Valve MXG-461 LED Status Indicators

LED Display

Status

Description

LED green

On continuously Automatic Mode (normal, no faults)

Flashing

- Mechanically set to MANUAL

- Mechanically set to OFF

- Currently in Auto-Calibrate Mode

LED red

On continuously

- General fault

- General calibration fault

- Microprocessor fault

Flashing

- Faulty 24 VAC supply (Too low)

LED

Off

- No 24 VAC supply

- Electronics Module fault

9. Turn off power to the Control Valve by setting the ECS/SP Control Box POWER switch to

the OFF position.

10. Replace and secure the Electronics Module cover by tightening the two captive screws.

WARNING!

MANUAL CONTROL OPERATION OF THE 3-WAY VALVE DISABLES THE OVER-
TEMPERATURE & POWER LOSS SAFETY SHUTDOWN FEATURES OF THE SYSTEM.
MANUAL OPERATION IS ONLY USED FOR PROBLEM DIAGNOSIS

.

«
...
27
28
29
30
31
...
»

Содержание AERCO SmartPlate SP150







































































































































Отзывы:

Нет отзывов

Похожие инструкции для AERCO SmartPlate SP150

Бренд: Lasko Страницы: 4

Бренд: Cadac Страницы: 8

Бренд: Eaton Страницы: 12

Бренд: Pahlen Страницы: 2

Бренд: vacuubrand Страницы: 76

Бренд: Walrus Страницы: 3

Бренд: Walrus Страницы: 5

Бренд: wallas Страницы: 18

Бренд: Calpeda Страницы: 43

Бренд: Etherma Страницы: 2

Бренд: Calienta Страницы: 58

Бренд: Maico Страницы: 16

Бренд: Pentair Страницы: 16

Бренд: Wilden Страницы: 43

Бренд: S&P Страницы: 24

Бренд: Yoshimasa Страницы: 7

Бренд: DOCRILUC Страницы: 31

Бренд: Predator Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды