Check Our Web Site For FAQs: www.wattstopper.com
9
SECURITY OVERRIDE
The EW sensors have an override-on feature which allows lights to be turned on for the set
time delay period.
• If there is an installed
switch
—turning the switch
off then on
, turns the lights on. If no
motion is detected by the sensor, the lights will remain on for the set
time delay period
(or
minimum of approximately one minute) and then turn off.
This will also happen when power is restored after a power outage.
Note:
If the lights do not turn on, the sensor may be inactive due to the daylight level. Turn
the switch off for 5 seconds, then turn it on. The lights should turn on as described above.
TROUBLESHOOTING
Lights do not turn off:
1. The sensor may be detecting movement outside the desired coverage area. The sensor’s lens
may need to be masked to block unwanted coverage (see Masking, page 2). If this does
not solve the problem, see step 2.
2. Test to see that the sensor is operating properly. Set the time delay to minimum (12 seconds).
Remain still, or move out of range of the sensor. If there is no movement in the coverage area,
the sensor should turn lights off in 12 seconds. Reset the time delay to the desired value.
- If the lights do not turn off, have a person qualified to check high voltage connections
verify that the sensor and lighting are wired correctly (see Wiring and Installation, page 5 & 6).
CAUTION:
Make sure power is turned off at the circuit breaker before checking wiring.
- If the sensor is wired correctly, call our Technical Support number.
Lights turn on when there is sufficient daylight:
1. Decrease the light level setting, as desired (counterclockwise toward the moon
icon)
(see Dial Adjustments, page 7 & 8).
Lights do not turn on:
1. If there is a controlling switch installed, make sure that it is turned on.
2. If the lights do not turn on when lights are needed—increase the light level setting, as
desired (clockwise toward the sun
icon) (see Dial Adjustments, page 7 & 8).
3. Have a person qualified to check high voltage connections verify that the sensor and lighting
are wired correctly (see Wiring and Installation, page 5 & 6).
CAUTION:
Make sure power is turned off at the circuit breaker before checking wiring.
- If the sensor is wired correctly, call our Technical Support number.
WARRANTY INFORMATION
The Watt Stopper, Inc. warranties its products to be free of defects in materials and workmanship
for a period of five years. There are no obligations or liabilities on the part of The Watt Stopper, Inc.
for consequential damages arising out of or in connection with the use or performance of this
product or other indirect damages with respect to loss of property, revenue, or profit, or cost
of removal, installation or reinstallation.
When ordering, add (-W) for Arctic White or (-G) for Architectural Gray to catalog numbers.
Catalog #
Description
EW-100-120
120VAC, 60Hz, 180° Outdoor/Indoor PIR Motion Sensor with Isolated Relay,
includes cover plate
EW-105-120
120VAC, 60Hz, 180° Outdoor/Indoor PIR Motion Sensor, includes cover plate
EWF-105-120 120VAC, 60Hz, 180° Outdoor PIR Motion Sensor, includes two lamp holders
and cover plate
EW-200-120
120VAC, 60Hz, 270° Outdoor/Indoor PIR Motion Sensor with Isolated Relay,
includes cover plate
EW-205-120
120VAC, 60Hz, 270° Outdoor/Indoor PIR Motion Sensor, includes cover plate
EWF-205-120 120VAC, 60Hz, 270° Outdoor PIR Motion Sensor, includes two lamp holders
and cover plate
EW-100-277
277VAC, 60Hz, 180° Outdoor/Indoor PIR Motion Sensor with Isolated Relay,
includes cover plate
EW-105-277
277VAC, 60Hz, 180° Outdoor/Indoor PIR Motion Sensor, includes cover plate
EW-200-277
277VAC, 60Hz, 270° Outdoor/Indoor PIR Motion Sensor with Isolated Relay,
includes cover plate
EW-205-277
277VAC, 60Hz, 270° Outdoor/Indoor PIR Motion Sensor, includes cover plate
ORDERING INFORMATION
10
Call 1(800) 879-8585 or 1(972)578-1699 For Technical Support
Outdoor incandescent lamp holders
Shrouds for PAR 20 & PAR 38 lamps
Round outdoor junction boxes & cover plates
THIRD-PARTY ORDERING INFORMATION
Additional color-matched lamp holder accessories are available through your local distributor,
or for further assistance call CANLET at 1-888-461-5307.
