Watt Stopper DT-300 Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 18

Watt Stopper DT-300 Скачать руководство пользователя страница 1

U.S. Patent: 7,277,012

Santa Clara, CA 95050

DT-300

v3

360° Dual Technology • Low Voltage

Occupancy Sensor

with Light Level, Isolated Relay and Manual On feature

Installation Instructions

Specifications

Voltage ..........................18-28VDC/VAC, half wave rectified AC
Current Consumption ........................................................25 mA
Power Supply .....................................WattStopper Power Packs
Isolated Relay Rating ........................................ 1A @30VDC/VAC
Operating Temperature .......................32° to 131°F (0° to 55°C)
Light Level One-Step Adjustment .........................10FC—300FC
Time Delay Adjustment ...................... 30 seconds to 30 minutes
Walk-Through Mode .....3 minutes if no activity after 30 sec
Test Mode ................................ 5 sec. upon DIP switch reset
PIR Coverage (Typical) .....................................................1300 ft

2

Sensitivity Adjustment .......High or Low (DIP switch setting)
Ultrasonic Coverage (Typical) ..........................................1300 ft

2

Sensitivity Adjustment .........................Min. to Max. (trimpot)
Frequency......................................................................40kHz
UL & CUL Listed for use with WattStopper Power Packs

1
2
3
...
»

Содержание DT-300



















Отзывы:

Нет отзывов