background image

Page

Thank you for purchasing the WattAge Fokker Dr.1 Triplane EP ARF.  We're confident that the quality of your new airplane 
meets and even exceeds your expectations.  Before completing the final assembly of your new airplane, please carefully 
read through this assembly manual in its entirety.  Doing so will ensure your success the first time around!

This assembly manual is designed to guide you through the entire assembly process of your new airplane in the least amount of time 
possible.  Along the way you'll learn how to properly assemble your new airplane and also learn tips that will help you in the future.  
We have listed some of our recommendations below.  Please read through them before beginning assembly.

  Please read through each step before beginning assembly.  You 

should find the layout very complete and straightforward.  Our goal 

is to guide you through assembly without any of the headaches 
and hassles that you might expect.

  There  are  check  boxes  next  to  each  procedure.    After  you 

complete a procedure, check off the box.  This will help prevent 
you from losing your place.

  Cover your work table with brown paper or a soft cloth, both to 

protect the table and to protect the parts.

  Keep a couple of small bowls or jars handy to put the small parts 

in after you open the accessory bags.

  You might be excited to get your new airplane in the air, but take 

your time.  This will ensure you build a straight, strong and great 

flying airplane.

  If you come across this symbol 

,  it means that this is an 

important point or an assembly hint.

tAble oF Contents

This R/C airplane is not a toy! If misused or abused, it can cause serious bodily injury and/or damage to property.  Fly only in open 

areas and preferably at a dedicated R/C flying site.  We suggest having a qualified instructor carefully inspect your airplane before 
its first flight.  Please carefully read and follow all instructions included with this airplane, your radio control system and any other 

components purchased separately.

WattAge guarantees this kit to be free from defects in both material and workmanship at the date of purchase.  This does not cover any component 

parts damaged by use, misuse or modification.  

in no case shall WattAge's liability exceed the original cost of the purchased kit.

In that WattAge has no control over the final assembly or material used for final assembly, no liability shall be assumed for any damage resulting from 
the use by the user of the final user-assembled product.  By the act of using the final user-assembled product, the user accepts all resulting liability.

Introduction ..............................................................................................2

Safety Warning ........................................................................................2

Our Guarantee.........................................................................................2

Customer Service Information .................................................................3

Our Recommendations............................................................................3

Lithium Polymer Battery Warnings - Please Read ..................................4

Tools and Supplies Required ...................................................................5

Kit Contents .............................................................................................5

Tips From the Pros ..................................................................................6

Motor and Cowling Installation ................................................................7

Stabilizer and Rudder Installation ............................................................9

Elevator and Rudder Control Systems Installation ................................ 11

Landing Gear Installation.......................................................................13

Bottom and Center Wing Installation .....................................................15

Aileron Control System Installation........................................................17

Top Wing Installation .............................................................................19

Final Assembly ......................................................................................20

Balance Point and Control Throws ........................................................22

Preflight Check and Safety

 ....................................................................22

Product Evaluation Sheet ......................................................................23

introDuCtion

sAFety WArning

our guArAntee

Содержание Fokker Dr.1

























Отзывы: