Watson-Marlow 323Du Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 48

background image

Watson-Marlow 323E, 323S, 323U and 323Du User Manual

22

16 MemoDose

The pump can dispense a set quantity or dose of fluid each time the key is pressed.
This is the MemoDose facility.

Set the pump
speed and direc-
tion. Place a suit-
able measuring
container at the
outlet and

START

the pump.

When the required vol-
ume of fluid has been
dispensed, press the

STOP

key twice within

half a second. This
starts the MemoDose
feature.

The pump has made a record of the fluid it has just dispensed.
You may now repeat this dose or adjust the quantity as required.
The display will show “

dos

“ for 3 seconds. Then the display will

change to show 100%.

S, U, Du

Measure the quantity of fluid which has been dispensed. If the quantity is
correct press

START

to repeat the dose.

If the initial dose is larger than required use
the

DOWN

key to reduce the volume %

showing on the display. This will reduce the
next dose to be dispensed by the pump.

If the initial dose was smaller than
required use the

UP

key to increase

the next dose to be dispensed by
the pump.

Press

START

. The pump will dispense the new dose

and the display will count down as this dose proceeds.
The pump will stop when the new dose is complete.

Measure the new dose. If it is correct you may now
repeat this dose as often as required. The keypad
lock can be used to prevent further changes.

Use the

UP

and

DOWN

keys to further adjust the

dose until the correct quantity is obtained. You may
adjust the dose size down to 1% or up to 999%

Press the

STOP

key twice within half a second to exit MemoDose

and return to manual operation.

«
...
20
21
22
23
24
...
»

Содержание 323Du

















































Отзывы:

Нет отзывов

Похожие инструкции для 323Du

Aquarea WH-MDF06E3E5 series

Бренд: Panasonic Страницы: 36

Бренд: York Страницы: 16

Бренд: TapFlo Страницы: 35

Бренд: Rainman Страницы: 17

Бренд: Danfoss Страницы: 38

Бренд: DAYLIFF Страницы: 12

Бренд: Zodiac Страницы: 23

Бренд: Walchem Страницы: 31

Бренд: Panasonic Страницы: 20

Бренд: Enviroheat Страницы: 20

Бренд: Enviroheat Страницы: 29

Duro Titan SBA025T1

Бренд: Canature WaterGroup Страницы: 8

Бренд: Pfeiffer Vacuum Страницы: 46

Бренд: Walrus Pump Страницы: 12

JABSCO 18670 Series

Бренд: Xylem Страницы: 16

Бренд: Honda Страницы: 25

Бренд: GORMAN-RUPP PUMPS Страницы: 31

Бренд: Fairland Pioneer Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды