A
Alarms, 49
Alarm Codes, 50
Almost Ready to Run, 22
Analog Retransmit, 52
0
opening the
1500, 5, 32
Overview, Input & Output Fig.
1.4
Overview, Operating Modes, Fig. 5, 9
Overview, MNTR DATA, Fg. 7,13
B
Overview, CHG DATA, Fig. 8.14
Before You Begin (Programming), 18
Overview, CHG PARA, Fig. 9.15
Bad Sensor, 74
P
C
Packing List, 5
Change Data Flow Diagram, Fig. 20,42
Pre-installation Information, 32
CHG DATA Overview, Fig. 8,14
Programming, 16-2540-48
Change Parameter Flow Diagram, Fig. 21,46
Programming Chart, Chart 6,57
CHG PARA Overview, Fig. 9,15
Proportional Band, 47
Cycle Time, 48
Q
D
Quick Reference, 90
Data Comm. Commands and Syntax, 61
Quick Wire, 7
Data Comm. Error Codes, 73
Quick Wire AC Power Connections, Fig. 3, 7
Dimensions, Unit and Panel Cutout, Fig. 13, 33
Quick Wire Simulated Sensor Wiring, Fig. 4, 8
DIP Switches, 6, 18,40
Clear Memory, 18
How to Set, 6
Position and Function, Table 1, 6
Display and Keys, 10
Dry Bulb Installation, RTD, 26
E
Electrical Connections and Wiring, 34-38
Enter Real Time, 18
Entering Data, 19
Error Codes, 73
Event Input, 36.51
Event Outputs, 51
F
Front Panel Components, Fig. 6,
10
Flow Diagrams, Fig. 20,42
G
RTD General Parameter Chart, Chart 4,55
T/C General Parameter Chart 5,56
RTD Guarded Access Chart, Chart 2.53
T/C Guarded Access Chart, Chart 3,54
H
Halt Conditions, 22
Helpful Hints: 22-24
Ramping Conditions, 23
Wait-Step, 23
Jump Loop Step, 24
Recycle, 24
I
Installation Procedure, 34
R
Ramping Conditions, 23, 43
Rate, 48
Rate
Band,
48
Recycle Option, 24.41
Remote Hold, 36,51
Reset, 47
Returning Merchandise, 83
RTD Installation Guidelines, 26
Run and Halt a Program, 60
S
Sample Program, 16
Programming Step 1, 19
Programming Step 2.20
Programming Steps 3 through 6,21
Programming Step 7, Jump Loop Step, 21
Programming Step 8, 21
Program Chart, Chart 1.17
Program Event Outputs, Table 2, 17
Program Steps, Table 3,2l
Setting Event Outputs, 17
Shipping Claims, 84
Software, Overview, 12
Specifications,
80
Start Your Program!, 22
Syntax, 64-72
T
Temp-RH Selection, 26
T/C Installation Guidelines, 27
Temp-Temp Selection, 26
Tuning, 59
Interface RS-422/423-Pins, Fig. 19,38
Introduction, Read Me First, 4
J
Jumper, Input Selection, 35
Jumper, RS423/422 Selection, 38
Jump Loop Step (JL), 24
M, N
Model # Information, 82
Modes, Operating Overview, Fig. 5,9
Monitoring the Action, 22
MNTR DATA Overview, Fig. 7,13
Noise, reduction of,
27-28
Non-Ramping Set
Point, 9, 13
U
V
w
Wait Step,
Warranty Information, 83
Watlow RTD’s, 26
Watlow Winona, Inc., 84
Wet Bulb Installation, RTD, 26
Wiring, Control, 36
Wiring Data Comm., 39
Wiring, Disable Ch-2.38
Wiring, Input, 36,37
Wiring, Output, 36,37
Wiring, Power, 38
Wiring Practices for
Preventing Noise, 27-28
Index,
Appendix
WATLOW Series 1500 User’s Manual
89