Waters Xevo TQD Скачать руководство пользователя страница 98

Страница: 98 / 250

4-22

Maintenance Procedures

Gas ballasting the roughing pump

Note:

This procedure is not required for an oil-free roughing pump.

Roughing pump:

The roughing pump draws large quantities of solvent vapors. The vapors tend

to condense in the pump oil, diminishing pumping efficiency. Gas ballasting

purges condensed contaminants from the oil.
Gas ballast the roughing pump when these conditions apply:

•

With ESI operation, once a week.

•

When the roughing pump oil appears cloudy.

•

When the vacuum pressure is higher than normal.

•

When condensate forms in the roughing pump exhaust line.

•

When you change the roughing pump oil.

The roughing pump can be fitted with either of the following:

Caution:

Failure to routinely gas ballast the roughing pump shortens oil

life and, consequently, pump life.

TP02689

Oil filler plug

Oil-level sight glass

Drain plug

Gas ballast valve

Exhaust port flange

Содержание Xevo TQD


























































































































































































































































Результаты поиска

Содержание Xevo TQD

Отзывы:

Похожие инструкции для Xevo TQD

Бренды по названию

Популярные бренды

Waters Xevo TQD, Руководство оператора, обзор и техническое обслуживание

Результаты поиска

Содержание Xevo TQD

Отзывы:

Похожие инструкции для Xevo TQD

Бренды по названию

Популярные бренды