Waters ACQUITY Arc System Скачать руководство пользователя страница 23

Страница: 23 / 86

• To prevent band spreading, ensure that the tubing is fully bottomed in the fitting

before tightening the compression screw.

• For easier accessibility, use long compression screws to attach tubes to the

injector and vent valve.

• Perform the solvent manager leak test whenever you replace or loosen fittings

during maintenance (see the console online Help).

• Whenever you loosen fittings during maintenance, examine for cracks, stripped

threads, and deformations.

• Do not reuse stainless steel fittings more than six times.

2.5.1.1 Long 1/4-28 fitting with flangeless ferrule and stainless steel lock

ring installed on 1/8-inch OD tubing

First use or re-installed

Compression screw

Lock ring

Ferrule

End of lock ring with larger inside diameter (ID)

Tighten the fitting finger-tight.

June 12, 2015, 715004747 Rev. A

Page 23

Содержание ACQUITY Arc System






















































































Результаты поиска

Содержание ACQUITY Arc System

Отзывы:

Waters ACQUITY Arc System, Системное руководство, Страница: 23 / 86

Результаты поиска

Содержание ACQUITY Arc System

Отзывы: