WATERS NETWORK SYSTEMS
ProSwitch-Xtreme Operating Manual
Page 5
4.0 SPECIFICATIONS
4.1 Technical
Specifications
Ports Performance
Fiber, and when an auto-negotiating port is operating at 100Mbps: Data Rate: 100Mbps
When an RJ45 auto-negotiating port is operating at 10Mbps:
Data Rate: 10Mbps
Network Standards
100Mbps: Ethernet IEEE 802.3u, 100BASE-TX, 100BASE-FX
10Mbps: Ethernet IEEE 802.3, 10BASE-T
Auto-sensing for speed: IEEE 802.3u
Packet-Processing Between Domains
Filtering and Forwarding Rate from 100Mbps ports:
148,800 pps max
Filtering and Forwarding Rate from 10Mbps ports:
14,880 pps max.
Processing type: Store and Forward
Auto-learning: 16K address table, shared for all traffic domains
Packet buffers: 1.0Mb, dynamically shared on all domains
Latency (not including packet time):
100 to 10Mbps: ...................................... 5
µ
s
10 to 100Mbps: 5
µ
s
Path Delay Value
: 50 BT on all ports
Maximum Ethernet Segment (or Domain) Lengths
10BASE-T (Unshielded twisted pair)
100 m (328 ft)
100BASE-TX (CAT5 UTP)
100 m (328 ft)
100BASE-FX, full duplex: (multimode)
2.0 km (6,562 ft)
100BASE-FX, full duplex: (singlemode)
20.0 km (65,620 ft)
Operating Environment
Ambient Temperature: -40
°
F to 160
°
F (-40
°
C to 70
°
C)
Plenum rated, cold start down to 20
°
C
Storage Temperature: -40
°
to 185
°
F (-40
°
C to 85
°
C)
Ambient Relative Humidity: 10% to 95% (non-condensing)
Altitude: up to 15,000 ft. operating
Power Supply (External): AC Power Supply (PSX-A) for ProSwitch-Xtreme-5V
AC Power Connector: IEC-type, male recessed at rear of Power Supply chassis
Input Voltage: 85 to 264 VAC (auto-ranging)
Input Frequency: 47 to 63 Hz (auto-ranging)
Power Consumption: 15 watts typical
Power Supply Rating: 3Amps at 5VDC
Network Cable Connectors:
6 RJ45 shielded female ports and 2 fiber port
100Mbps: Category 5 UTP/STP, fiber (50/125, 62.5/125 mm, or singlemode at 9/125 micron)
10Mbps: Category 3, 4, 5 UTP (Note: auto-sensing does not sense cable type)
Full-duplex / Half duplex on copper (RJ45) switched Ports # 2 to 7
All the RJ45 ports support Full/Half duplex and 10/100Mbps speed, each independently auto-negotiating.
Fiber Ports # 1 and 8
The switched fiber ports #1 & 8 are fixed at full-duplex only, 100Mbps speed.
Mechanical
Enclosure: Rugged 18-gauge high-strength steel case. Metal mounting plate included.
Suitable for stand-alone, shelf, pedestal or wall mounting: The case also serves as a heat sink. The metal
mounting base is included, 13-gauge steel. Mounting holes in the base plate are a rectangle that measures
3.35” x 8.25” (8.5 cm x 21.0 cm). The lip at the bottom of the base can be used to anchor strain-relief for
cables.
Dimensions Base Unit: 1.50” x 5.75” x 8.75” (3.8 cm x 14.6 cm x 22.2 cm)
Power Supply: 1.25” x 5.75” x 6.50” (3.2 cm x 14.6 cm x 16.5 cm)
Weight: Base Unit: 6.45 lb. (2.9 kg.)
Power Supply: 5.2 lbs (2.4 kg)
Cooling method: Convection, with case operating as a heat sink.
Note: Internal steel plates conduct heat from the electronic elements inside to the ProSwitch-Xtreme steel
case, which acts as a heat sink. Internal chip temperatures are only about 10
°
C above case ambient during
steady state operation