waterpowered Hello Bidet, Руководство пользователя

Страница: 9 / 10

9
HOW TO USE HELLO BIDET
1) Using dry hands for a better grip, insert the quick
connector (B) to the special filter holder (A1 -A2)
or Addy (O) turning counterclockwise (fig. 6a - 6b);
2) Turn on the faucet, press the lever (F) and adjust
the temperature of the water that comes out of
the handshower (E) by checking it with your hand
(fig. 7). Regarding water temperature, keep in mind
that the skin sensitivity of intimate areas is always
higher compared to the sensitivity of hands; Never
use with water above 38°C/100°F.
3) Sit on the toilet, position the handshower (E)
between your legs and press the lever (F) in order
to begin the cleansing of your intimate areas (fig.
8); the lever (F) will allow you to interrupt the
water flow at any time by simply releasing the
lever.
4) When you are finished, release the lever (F) and
turn off the water from the faucet;
5) Unplug the quick connector (B) from the faucet
filter by turning clockwise;
6) At the end of each cleansing, after having rinsed
out the bidet handshower (fig. 10), blow air into
the attachment connector part (B) in order to get
rid of any remaining water left in the tube (fig. 11)
and by simultaneously pressing the control (F) of
the bidet handshower (E).
FREQUENCY AND DURATION OF CLEANSINGS
• The cleansing of your intimate areas with Hello
Bidet can be performed as often as you like, even
several times a day;
• The total duration of a cleansing is absolutely up to
your personal desires.
MAINTENANCE AND STORAGE
• Before use, connect Hello Bidet to the faucet and let
the water run for about 20-30 seconds until it exits the
handshower;
• Between uses, we recommend keeping the product
thoroughly clean, dry and stored inside its carrying
case;
• When cleaning the product, do not use harsh
detergents so as to avoid damaging the rubber or
plastic parts.
UNIVERSAL ADAPTER ADDY
Included only with Hello Bidet “Travel” version. It can
be purchased separately as an accessory for the Hello
Bidet “Basic” version.
Thanks to the Addy adapter, you can connect Hello
Bidet to the faucet in a simple and fast manner,
without the need to mount the special filter holder .
Addy is ideal for use on the road, in a hotel or in case
of faucets with non-standard threads.
Addy can be connected to all faucets with circular
filter holder for water outlet with an outer diameter
from 16mm to 25mm and with a minimum height of
5mm (fig.12).
WARNINGS AND RECOMMENDATIONS FOR THE USE
OF ADDY
• Gradually open the tap, not suddenly and not the
maximum water pressure;
• While the tap is open, do not try to reposition or
move Addy to avoid leaks;
• Initially, there may be some small leakage of water
from top of Addy for a few seconds, that are going
to disappear quickly. If the leakage were to be
prolonged or if it is excessive, you should repeat
the installation procedure of Addy to the faucet;
• Make sure the filter holder is securely tighten to
the faucet to prevent leakage when the adapter
is mounted;
• The use of Addy in case of excessive pressure while
mounting, and repeated use on the same tap, may
cause light marks on the filter holder of the faucet
due to contact with the screws (for extended use
of Hello Bidet on the same faucet, we recommend
using the threaded special filters);
• It is not recommended to leave Addy mounted to
the faucet; if this happens, before each use check
that the hold is solid, making sure that the screw
(P1) is tightened;
• When tightening the screw (P1) be careful not to
deform the ring (Fig. 14);
• Should Addy come off the faucet, repeat the
procedure of assembly Addy to the faucet,
tightening the screw P1 and the adjustment wheel
P2;
• Do not disassemble the components of Addy;
• Contains small parts - keep away from children.
ADDY - ASSEMBLY TO THE FAUCET
1. Place the lever in the open position (Fig. 13) and
tighten the adjustment wheel (P2) until the lever is
pulled, but without using excessive force;
2. Check that the tightening screw is sufficiently
loosened to allow the insertion of Addy on the