WaterGroup WG185ACF75 Скачать руководство пользователя

Страница: 3 / 23

Proper Installation

This water filter system must be properly installed and located in accordance with the

Installation Instructions before it is used.



Do not

install or store where it will not be

exposed to temperatures below freezing or
exposed to any type of weather. Water

freezing in the system will break it. Do not
attempt to treat water over 100°F.



Do not

install in direct sunlight. Excessive

sun or heat may cause distortion or other
damage to non-metallic parts.



Properly ground to conform with all gov-
erning codes and ordinances.



Use only

lead-free solder and flux

for all

sweat-solder connections, as required by

state and federal codes.



Maximum allowable inlet water pressure is

125 psi. If daytime pressure is over 80
psi, night time pressure may exceed the

maximum. Use a pressure reducing valve

to reduce the flow if necessary.



WARNING:

Discard all unused parts and

packaging material after installation. Small
parts remaining after the installation could

be a choke hazard.

Содержание WG185ACF75
























Результаты поиска

Содержание WG185ACF75

Отзывы:

Похожие инструкции для WG185ACF75

Бренды по названию

Популярные бренды

WaterGroup WG185ACF75, Руководство пользователя

Результаты поиска

Содержание WG185ACF75

Отзывы:

Похожие инструкции для WG185ACF75

Бренды по названию

Популярные бренды