manualshive.com logo in svg

WaterFurnace Synergy3D, Руководство по установке

Поделиться
Скачать
WaterFurnace Synergy3D Скачать руководство пользователя страница 22

22

SYNERGY3D INSTALLATION MANUAL

Microprocessor Control Operation

Heating Operation

Heat, 1st Stage (Y1)

The blower motor is started on low speed immediately, the 
loop pump is energized 5 seconds after the “Y1” input is 
received, and the compressor is energized on low capacity 
10 seconds after the “Y1” input. The blower is switched to 
medium speed 15 seconds after “Y1” input (ECM only).

Heat, 2nd Stage (Y1,Y2) Dual Capacity Units

The second stage compressor will be activated 5 seconds 
after receiving a “Y2” input as long as the minimum first 
stage compressor run time of 1 minute has expired. The 
ECM blower changes from medium to high speed 15 
seconds after the “Y2” input.

The Comfort Alert will delay the second stage compressor 
until 5 seconds after it receives a “Y2” from the board.

Heat, 3rd Stage (Y1,Y2,W) Dual Capacity Units

The 1st stage of resistance heat is energized 10 seconds 
after “W” input, and with continuous 3rd stage demand, the 
second stage of resistance heat will engage after 5 minutes.

emergency Heat (W Only)

Low speed blower and damper output CR3 will be 
energized immediately after receiving (W only). The first 
stage auxiliary heater will be energized 10 seconds upon 
receiving a (W only) and the blower will shift to high speed 
15 seconds after receiving a “W” only input. If the “W” input 
is not removed, the second, third, and fourth auxiliary heat 
outputs will stage on, one at a time, every two minutes.

Cooling Operation

Cool, 1st Stage (Y1,O) 

The blower is started immediately, and the loop pump(s) 
is energized 5 seconds after the “Y1” input is received. The 
compressor will be energized (on low capacity for Dual 
Capacity units) 10 seconds after the “Y1” input. The ECM 
blower will shift from low to medium speed 15 seconds 
after the “Y1” input. 

Cool, 2nd Stage (Y1, Y2, O) Dual Capacity Units

The second stage compressor will be activated 5 seconds 
after receiving a “Y2” input as long as the minimum first 
stage compressor run time of 1 minute has expired. The 
ECM blower changes to high speed 15 seconds after the 
“Y2” input. The Comfort Alert will delay the second stage 
compressor until 5 seconds after it receives a “Y2” from the 
board.

Hydronic Cooling Slave Signal (24 vac input on P6-
pin 15 violet wire)

The Synergy3D control board must be operating in cooling 
mode (Y1 and O inputs) or the cooling slave signal is 
ignored. When “Y1”, and “O” inputs have been received 
and a cooling slave input from heating/cooling thermostat 
located in a hydronic heated/force air cooled zone are 
received the control will activate CR3 relay to open 
damper(s) which will allow for cooling to occur in zone. 
When cooling slave input (24VAC) signal is removed the 
control will turn off the CR3 relay output, if spring damper 
operation is selected, or activate, the  CR4 output if POPC 
damper operation is selected. This will close field installed 
damper(s) located in ductwork. 

NOTe:

 The control will not operate in forced air cooling and 

hydronic water heating modes simultaneously. 
 

SW4 (Status Board Switch)

In the OFF position, the hydronic mode is disabled and 
the damper connected to CR3/CR4 is opened. The switch 
must be in the ON position to enable the hydronic mode. 

NOTe:

 If the status board is not connected to the MCB, the 

hydronic mode is disabled.

Hydronic Operation

Over-ride time SW3-4 SW3-5
5 minutes

15 minutes
30 minutes
60 minutes

On
Off
On
Off

On
On
Off
Off

Over-Ride Selection

S

ta

tu

s 

LE

D

 P

C

B

  

17

P

50

3A

01

  R

ev

 A

SW4

R

R

R

R

R

G

Y

R

SW3 (4 and 5 Override Switches)

These DIP switches configure the time that the unit will 
run in the current mode of operation if it is not the priority 
mode (SW2 #3 FAH/Hydronics) of operation selected. 
Example: If the unit is operating in hydronic mode, forced 
air heat (SW2 #3 is OFF) is the priority. A Y1 call from the 
FAH zone is present at the MCB. When SW3 numbers 4 and 
5 are both in the ON position, the unit will operate in the 
hydronic mode for five minutes. If the hydronic call is not 
satisfied within the five minutes, the unit will switch to FAH 
mode. When FAH is satisfied, the unit will switch back to 
hydronic.

All manuals and user guides at all-guides.com

Содержание Synergy3D









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды