manualshive.com logo in svg

WaterFurnace GeoLink FC1-FPT, Руководство по установке

Поделиться
Скачать
WaterFurnace GeoLink FC1-FPT Скачать руководство пользователя страница 5

5

FLOW CENTER INSTALLATION AND LOOP FLUSHING MANUAL

To

Fitting(s)

Rubber Hose Kit

1

" MPT to 1" barbed (PVC or brass)

PVC

1

" MPT to 1" glue socket or 1" MPT nipple

PE

Use brass barbs and double clamp or PE to brass adapter

Copper

1" MPT x 1" sweat and solder before connecting to FC1S, FC2S or 1" MPT nipple

Connection Options

Mounting

 The 

fl ow center must be mounted with the pump center shaft in the horizontal position. The only adjustment is that the 

circulator pump electrical boxes be on the horizontal side of the power head in the mounted position to help prevent mois-
ture from being held inside the box (see Figure 1).  

  •   Side of unit mounting notes: 

The fl ow center can be mounted by using  

 

 

  four sheet metal screws directly into the unit   

 

  cabinet on the side opposite the air coil.  Be 

careful not to puncture any internal parts of 
the unit when inserting screws into the 
cabinet. 

 • 

 

Unfi nished wall (bare stud)  mounting notes: 
The assembled fl ow center can be mounted 
by using four lag screws into two 19-inch (48  

 

  cm) cross braces spanning 16 inches (41 cm)

on center studs or by using lag bolts through 
center of brackets into one stud.

 

•   Finished wall (drywall) mounting notes: 

  The 

fl ow center can be mounted by using two 

 

  lag screws through drywall into stud through 

 

  center holes in top and bottom of cabinet. 

Notes:

 Insulation should be used on all inside piping 

when minimum loop temperatures are expected to be 
less then 50° F (10° C). Use table below for insulation 
sizes with different piping sizes. 

Recommended Insulation

Piping

Description

1

" IPS Rubber Hose

1-3/8

" 

ID - 1/2

" Wall

1-1/4

"

 IPS PE

1-5/8

" 

ID - 1/2

" Wall

2

" 

IPS PE

2-1/8

" 

ID - 1/2

" Wall

Figure 1: Pump Mounting

Pump mounting and instructions. The pump contains a ceramic impeller
center shaft and is water lubricated. Therefore, shaft

MUST ALWAYS

be

in horizontal position only for proper operation and longevity.

.

OK

OK

Horizontal

OK

NO

Vetical Center
Shaft Position

Vetical Center
Shaft Position

NO

Pumps

MUST ALWAYS

be

mounted so ceramic center
shaft is in horizontal position

ONLY

Rotate pump head so electrical box is on the side or top only. Never leave
electrical box on the botton of pump head (pump windings may short out).

Pumps should never
be mounted in these
positions. The ceramic
center shaft shown is in
the vertical position.
Operating pumps
installed in this manner
will damange the pump.

General Installation Information (cont.)

Содержание GeoLink FC1-FPT

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды