INSTALLATION GUIDE
Important!
Adherence to all local and municipal building, plumbing
and electrical codes as they pertain to the installation of
the WaterCop
®
PRO System is of utmost importance.
Codes in some areas may require that a licensed
plumber be employed to do the installation, or that the
proper permits be obtained prior to any installation.
Even if local codes do not require a licensed plumber to
do the installation, it is necessary that the installer has
a professional level of competence in both plumbing
and electrical skills to perform the installation. These
instructions assume this level of knowledge and skill. If
in doubt, use a licensed professional.
Common Displays on WaterCop
®
PRO
Valve is open and all
components functioning.
Water was turned off via local
controls.
Flood sensor #1 (probe 1)
detected water and turned valve
off.
#2 hard wired sensor from
monitoring station detected
water and turned valve off.
Probe on sensor #3 (probe 2)
is shorted. Water is still on.
Probe needs to be checked
and repaired to allow proper
function.
Probe on sensor #2 is cut or
disconnected. Water is still on.
Probe needs to be repaired
or replaced to allow proper
function.
Monitoring station has lost
power or is out of range.
Battery in sensor #2 is low and
needs to be replaced.
These are the text display codes on both the WaterCop
®
PRO valve and monitoring station (optional).
4
WATERCOP
NORMAL
WATERFCOP
WATER IS OFF
! ALARM !
SENSOR #1 WET 1
! ALARM !
WIREPANEL WET 2
***ALERT***
SENSOR #3 SHT 2
***ALERT***
SENSOR #2 OPN 1
***ALERT***
WIREPANEL LOST?
***ALERT***
SENSOR #2 BAT
Flow Data
Valve Size Cv = Gpm flow @ 1 PSI pressure drop
1/2" NPT
19
3/4" NPT
34
1" NPT
52
1-1/4” NPT
77
For cold water applications.
FCC Information
This equipment has been tested and found to
comply with the limits for a class B digital device,
pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses and can radiate radio
frequency energy and if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and
receiver.
•
Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
•
Consult the dealer for help.
Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2)
this device must accept any interference, including
interference that may cause undesired operation of
the device.
The user is cautioned that changes and modification
made to the equipment without the approval of the
manufacturer could void the user’s authority to
operate this equipment.
LIMITED WARRANTY
DynaQuip Controls Corporation warrants the electrical
components of the WaterCop
®
PRO
System to be
free from defects in material and workmanship under
normal use and if properly installed for a period of two
years from the date of purchase. If found to be defective
as mentioned above, it will be replaced or repaired if
returned prepaid along with proof of date of purchase.
This shall constitute the sole remedy of the purchaser
and the sole liability of DynaQuip Controls Corporation.
To the extent permitted by law, the foregoing is exclusive
and in lieu of all other warranties or representations
whether expressed or implied, including any implied
warranty of merchantability or fitness. In no event shall
DynaQuip Controls Corporation be liable for special or
consequential damages.
The WaterCop
®
PRO
brass ball valve has a lifetime
warranty.