Your cleaner has a unique patented vacuum head which has been supplied from the factory with all eleven (11) wheels installed. This configura
-
tion should function well to clean most pools. The vacuum head can be adapted for specific pool surface situations by adding brushes in different
configurations.
NOTE: Inserting the brushes into the vacuum head may require a good deal of force.
If you have difficulty, you may find it easier
to insert them by placing on a hard surface and pushing down on the head.
Wheels or Wheels and Brushes must be installed prior to use. Water Tech is NOT responsible for damages to pool surfaces if neither
the wheels nor brushes are installed in the vacuum head before use
.
Installing the Filter Bag
Please follow these instructions carefully:
•
Place the cleaner on its end on a stable and secure surface.
•
Place the filter bag/seal ring (part no.PROW022AP) into the cleaner. Make sure the rubber seal ring sits on the funnel. All of the filter bag
must be inside the funnel to ensure the head closes fully.
•
Put the nose cap (part no.PROA002) on the funnel.
•
Close the latch, squeezing the filter bag/seal ring in between.
NOTE:
You should not need to apply excessive force in order to close the latch. If you have trouble, make sure the filter bag is not trapped in
between the seal and the nose cap or funnel and there are no other obstructions such as sand or debris.
Installing the Battery Pack
•
Unlatch and Remove the Motor Box Cap
•
Line up the guides on the Battery Pack and on the switch plate. Apply gently pressure until the Battery Pack is seated properly. If you
encounter resistance, Remove the battery Pack, check alignment of the guides and apply gentle pressure again until battery is in place.
•
Replace the Motor Box Cap. Please note that the Motor Box Cap is designed to be installed in one orientation.
Once your cleaner is set-up for use, you may put it in your pool or spa.
•
Bring your cleaner to the side of the Pool or Spa and turn it “ON”
by sliding the switch to the left .
•
This appliance is designed to be in water only when in the “ON” position
and has battery power. Never leave your cleaner in the water when it is off.
NOTE:
Lift the cleaner from pool with the nose facing up to allow the water to escape from the back and sides while trapping debris inside the unit.
Preparing the Cleaner for Use
Setting up the Vacuum Head (PRO 900)
CAUTION: This cleaner is designed for underwater use only. Do not attempt to use your cleaner to clean anything
other than a pool or spa. It is not intended for use as an all-purpose vacuum cleaner. Unit must be submerged in water to operate properly.
Maximum operating temperature is b5DEGC (41˚F) and +40DEGC (104˚F). Maximum operating depth is 4 meters (15 ft)
Your cleaner is designed for use in 4 different ways to vacuum your pool or spa:
1. Vacuum using the handle and the vacuum head removed.
2. Vacuum using the handle and attached vacuum head, with either wheel or brush attachments depending on pool type.
3. Vacuum using a standard vacuum pole (not supplied) with the attached vacuum head.
4. Vacuum using the handle with the Head and Hose Attachment
WARNING:
Never use your cleaner
without the filter bag/seal ring and nose cap properly in place. Doing so will VOID the warranty.
Using a standard pole
The pole attachment on your cleaner is designed to accommodate any standard 1.25” diameter
pole. To attach a pole, simply press down on the alignment pins on the pole retaining spring clip.
Aligning the holes, slide the pole onto the cleaner and release the clip.
WARNING:
Do not lean on pole or use pole to support weight.
Cleaning Your Cleaner
For maximum cleaning efficiency the filter bag/seal ring should be checked, emptied, and cleaned after each use or whenever you notice that the
performance of your cleaner is declining.
To clean the filter bag/seal rin
g
•
Place the cleaner on its end (remove the vacuum pole, if attached).
•
Unlatch the Nosecap.
•
Remove the filter bag/seal ring by pulling it out of the funnel .
•
Invert the filter bag/seal ring and rinse with a garden hose or in a sink.
Note: Do not clean in a washing machine or with detergent.
•
Re-insert the filter bag when finished.
•
Note: Your reusable filter bag should be replaced if the seal ring is worn or if the bag is torn.
WARNING:
Keep away from children. Failure to comply with these warnings could result in fire and/or serious injury.
WARNING:
When servicing user serviceable parts, use only identical Water Tech replacement parts. Use of any other parts may
create a hazard or cause product damage.
Vacuum Head (Standard Assembly)
Meijer.com
