background image

©2012 Warn Industries, Inc.WARN® and the WARN logo are trademarks of Warn Industries Inc.

 2 

89548A0

N O T I C E

Equipment Damage

• 

Always refer to the Installation and Specification Guide, supplied in the winch kit, for all wiring schematics and specific details on how to wire this WARN product to your vehicle.

Read installation and operating instructions thoroughly.

  

 

C A U T I O N

Moving Parts Entanglement Hazard

FAILURE TO OBSERVE THESE INSTRUCTIONS COULD LEAD TO MINOR OR MODERATE INJURY

• 

Always take time to fully read and understand the installation and Operations Guide included with this product.

• 

Never operate this product if you are under 16 years of age.

• 

Never operate this product when under the influence of drugs, alcohol or medications.

Read installation and operating instructions thoroughly.

N O T E S

B E F O R E   Y O U   B E G I N

T A B L E   O F   C O N T E N T S

Parts List.........................................................................................................................................page 3

Tools Required .............................................................................................................................page 3

Torque Specifications ................................................................................................................page 3

Installation ............................................................................................................................. page 4-11

Maintenance/Care ................................................................................................................... page 11

Содержание 89535












Отзывы: