Warmup underlaminate Скачать руководство пользователя страница 4

Important!

WARNING

Once the foil heating mat has been installed avoid all traffic over the mat until the floor has been laid.

Do not install the foil heating mat until the floor is ready to be laid. If the floor is not being laid
immediately, all heating mats must be protected with two layers of cardboard or hardboard to
prevent damage.

Immediately prior to the floor being laid, check it has not been damaged in transit.

If you are in any doubt call the Warmup helpline on 

0845 345 2288

4

Please read carefully before installing your Warmup

®

underlaminate foil

heating mats.

DON’T  

leave insulating materials such as bean bags; linen or towels on the floor

surface. The maximum thermal resistance recommended between the heater 
and the room is 0.15 m2K/W (1.5 TOG).

DON’T

overlap heating mats. 

DON’T

fold or wrinkle Warmup

®

Underlaminate foil heating mats. 

DON’T

place heavy/sharp tools (or any other potentially damaging object)
on top of the heating mats.

DON’T

walk unnecessarily on the foil heating mats.

DON’T

install electrical cables or pipes under the floor with the foil heating mats.

DON’T

use cellulose insulation.

DON’T

install mats when the room temperature is below -5ºC.

DON’T

install foil heating mats anywhere except inside buildings.

DON’T

install foil mats under walls or partitions,or in areas under heavy cabinets,
closets, or fixtures (toilets, sinks, tubs, etc.).

DON’T

install foil mats within 30mm of any heat conductive building part, such as 
cold water pipes.

DON’T

install foil mats within 10mm of one another, 50mm of any wall, or 
150mm of a fireplace or hot water pipe. 

DON’T

connect any other electrical appliance on the same electric fused 

spur or RCD/SPUR unit of the heating system

DON’T 

install foil heating mats under wooden floor, if the wooden floor is thicker than

18 mm.

DON’T  

put accustic material between the foil heating mats and the wooden floor,

installing wooden type floor.

DON’T

use this heater under any floor covering other than wood or laminate 
flooring.

DON’T

place items on the floor surface which will stop the air flow or not allow heat

to rise into the room.

DON’T:

Содержание underlaminate






















Отзывы: