background image

4

SECTION 1: GENERAL

UNDERSTANDING YOUR SYSTEM:

Environ II panels are made of a pattern of a fi xed-resistance heating element, “sandwiched” between two layers of aluminium foil laminate.

This heating element is connected to a power supply cable, which exits the panel from one corner. The power lead is a three-core fl exible cord, which 
consists of three conductors (hot, neutral and ground) which are individually insulated and held together within a gray or white, outer “sheath” to form 
a single cable.

Various size panels are available, all prefabricated and tested in a carefully controlled factory environment.  

Available sizes are:

Heater details

The aluminium foil that forms the outer casing of the panel provides several advantages:

•  Heat generated by the heating element wire within the panel rapidly spreads through the foil, creating a large “plate” at an even temperature. 

This also helps to prevent heat build up under chair and table legs, as the natural tendency of the foil is to draw heat away from a hot spot;

•  It is waterproof, thus protecting all internal wiring and connections within the panel;
•  It is rigid, yet still suffi ciently fl exible to make for ease of installation;
•  It does not “ruck” or buckle when carpet is pulled or stretched over it.

The heating element is of a very special design, and uses materials carefully selected for an optimum balance of performance and safety.

•  Flexibility 
•  Tension and compression
•  Overheat protection

25-10-120 2  5  10 120.0 

120.0 

1.00 

120

26-10-120 2  6  12 151.4 

95.1 

1.26 

120

28-10-120 2  8  16 207.0 

69.6 

1.72 

120

210-10-120 2  10  20  241.2 

59.7 2.01 120

510-10-120 5  10  50  583.9 

24.7 4.87 120

515-10-120 5  15  75  827.7 

17.4 6.90 120

66-10-120 6  6  36 456.6 

31.5 

3.80 

120

610-10-120 6  10  60  723.6 

20.9 6.03 120

Product 

Code

Width

Feet

Length

Feet

Area Sq.

Feet

Power

Watts

Ohms

Amperage

Volts

25-10-240 2  5  10 120.0 

480.0 

0.50 

240

26-10-240 2  6  12 151.5 

380.2 

0.63 

240

28-10-240 2  8  16 207.3 

277.8 

0.86 

240

210-10-240 2  10  20  241.3 

238.7 

1.01 240

510-10-240 5  10  50  584.3 

98.6 2.43 240

515-10-240 5  15  75  872.5 

66.0 3.64 240

66-10-240 6  6  36 456.9 

126.1 

1.90 

240

610-10-240 6  10  60  670.5 

85.9 3.14 240

Product 

Code

Width

Feet

Length

Feet

Area Sq.

Feet

Power

Watts

Ohms

Amperage

Volts

Содержание ENVIRON II

















Отзывы: