Warmington Studio Oven Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 20

Warmington Studio Oven Скачать руководство пользователя страница 7

21 February 2017

All Dimension are in mm………….Copyright ©

7

Due to continued product improvement, Warmington Ind LTD reserves the right to change product specifications without prior notification.

DAMPER HANDLE FITMENT

STEP 2

Step 2 :

Align Screw on Damper Handle to the Hole in
the  Damper  Rod  on  the  Top  RH  Side  of  the
Studio  Oven  as  shown  .  (Using  a  3mm  Allen
Key Tighten screw  into the Damper Rod Hole
to secure in place)

STEP 1

Step 1 :

Slide Damper Handle over Damper Rod (Using a 3mm
Allen Key Tighten screw into the Damper Rod Hole to se-
cure in place)

SEISMIC RESTRAINTS

Step 2 :

Secure Fire down at 2X Lugs as Shown .

Seismic Bolts not Supplied .

Step 1 :

Lean Fire over to Bolt Seismic Re-
straints to Main Outer Wrap on the
back , bottom , inside as Shown
above .

DAMPER ROD MAINTENANCE - HIGH TEMPERATURE GREASE (COPPER COAT)

Step 1 :

Lift  or  Remove  Flue  System  from
the Fire to view the Damper Plate .
On  the  Damper  Plate  there  are  2x
Hinge  Bolts  ,  loosen  these  bolts  &
slide the Damper Rod out  from the
R/H  side  .  Ensure  to  hold  the
Damper  Plate  to  stop  it  falling  in-
side back of the Fire .

STEP 1

STEP 2

Step 2 :

Grease  end  of  Hinge  Bushes  &  Rod
with  High  Temp  Grease  to  ensure  the
Damper  Rod  Maintains  a  free  motion
back & forth .

STEP 3

Step 3 :

Slide  Damper  Rod  back  in  position
through  the  Side  of  the  Firebox  ,
ensure to hold Damper Plate in posi-
tion  when  sliding  the  Damper  Rod
back  in  place  ,  &  tighten  the  bolts  ,
once  set  in  same  position  as  when
you started .

Hold Damp-
er Plate to

stop from
falling down

Loosen Hinge Bolt

Slide
Damper

Rod Out .

Grease Bush-
es

Slide
Damper

Rod Out .

Seismic Restraint Fixing Instructions

Fix 2X Seismic Restraints through the Hearth into the Floor . They are to penetrate into the fixing by at least 3 times their
diameter.

Use at least 2 x 6 to 8 mm Dia Dyna Bolts or similar to fix fire to hearth and or through the hearth to the floor.

Fix hearth to floor with appropriate adhesive , bolt or screw.

Ensure that the Seismic Restraint complies with ASNZS 2918:2001— Ref 3.8

«
...
5
6
7
8
9
...
»

Содержание Studio Oven





















Отзывы:

Нет отзывов