WAREMA WMS-ZP Скачать руководство пользователя страница 3

Information on safety

2012324 [Rev. 1 - en]/2015-12-08

Page 3 | 14

1

Information on safety

Warnings are marked in the instructions with this
symbol.

Read through the product instructions before

use.
Observe all safety and setting instructions.

The basic safety instructions

can be viewed under

(

www.warema.de/Sicherheitshinweise

).

Target group

These instructions are intended for use by qualified fitters
(commissioning) and electricians (connections).

Permissible activities

Performing tasks on the product that are not described in
these instructions is not permissible. No other alterations
are to be carried out on the product other than as described
in these instructions without the written approval of
WAREMA.

Intended use

The drive is intended for operation of the following products:

Window awning with ZIP guidance

2

Commissioning

2.1

Information on the limit positions

Lower motor limit position

The drive has a position-controlled limit switch-off at the
bottom.

Upper motor limit position

The drive has a position-controlled limit switch-off at the
top.

2.2

Aids for commissioning

Test cable

(v

ene

tian blind swit

ch)

Ar

t. no. 634013

1

2

1 UP button

2 DOWN button

INFO

For WMS Hand-held

transmitters up to a

certain version (see label

on the back), Mode 1

needs to be performed

(for the procedure, see

the WMS Application

brochure).

Rev.D/M

WMS Hand-held tr

ansmitt

er basic 

(fr

ont) - Ar

t. no. 1002953

A

1

2

3

4

5

6

7

1 Control button

2 Automatic LED

3 UP button

4 STOP button

5 DOWN button

6 Comfort button

7 Transmission LED

WMS Hand-held tr

ansmitt

er 

(fr

ont) - Ar

t. no. 1002767

1
2

3

4

5

6

7

8

9

10

11

1 Control button

2 Control function dis-

play

3 Numbers display

4 Product buttons

5 UP button

6 STOP button

7 DOWN button

8 Comfort button

9 Scene button

10 Transmission LED

11 Info button

WMS Hand-held  transmitt

er (back)

1

2

1 Learn button

2 Mode button

Содержание WMS-ZP















Отзывы: