WAREMA EWFS Weather station plus Скачать руководство пользователя страница 3

Страница: 3 / 12

890464_k•en•2019-10-01

We reserve the right to carry out improvements

Wall mounting

Fig. 4 Wall mounting

Clip one of the included spacers in the threaded hole

(horizontally or vertically, Fig. 2).

Attach the weather station to a suitable substructure

using the included screws and dowels as shown

(Fig. 4).

The connecting cable must be correctly positioned in

the guide on the back of the mounting plate to ensure

it is not pinched during installation.

Ceiling installation

Fig. 5 Ceiling installation

Loosen the screw on the weather station joint.

Swing the mounting plate of the weather station up by

90° (or by the necessary angle).

Tighten the screw on the joint.

Clip one of the included spacers in the threaded hole

(horizontally or vertically, Fig. 2).

Attach the weather station to a suitable substructure

using the included screws and dowels as shown

(Fig. 5).

The connecting cable must be correctly positioned in

the guide on the back of the mounting plate to ensure

it is not pinched during installation.

Pole installation

Fig. 6 Pole installation and steel cable ties locking mechanism

Remove the thin (triangular) pieces at the top and

bottom edge of the mounting plate using a wire cutter

(Fig. 6

Pass the included steel cable ties through the mount-

ing plate openings as shown. The cable tie closures

must face outward.

Turn both ends of the cable tie inwards, one at a time,

using needle-nosed pliers.

Check that the weather station cannot be turned.

Содержание EWFS Weather station plus













Результаты поиска

Содержание EWFS Weather station plus

Отзывы:

Похожие инструкции для EWFS Weather station plus

Бренды по названию

Популярные бренды

WAREMA EWFS Weather station plus, Инструкции по эксплуатации и монтажу

Результаты поиска

Содержание EWFS Weather station plus

Отзывы:

Похожие инструкции для EWFS Weather station plus

Бренды по названию

Популярные бренды