W&H Lisa VA131-17 Скачать руководство пользователя страница 126 | Manualshive

Страница: 126 / 140

background image

126

LISA | Instructions for Use | VA131 2019 ENG Rev06 | 16/04/2020 | © 2020 W&H Sterilization Srl

Technical data

Water quality

FEED WATER SPECIFICATIONS (EN 13060)

Notice: Do not use rust inhibitor or any other agents in the clean
water tank.

This sterilizer uses distilled or demineralized water to generate
steam for the sterilization process. The table below lists the
maximum content of minerals and the specifications for the water
used for steam sterilization according to EN13060 ANNEX C.

Contaminants/minerals/qualities

Value/Specification

Total Dissolved Solids

< 10 mg/l

Silicon oxide, SiO2

< 1 mg/l

Iron

< 0.2 mg/l

Cadmium

< 0.005 mg/l

Lead

< 0.05 mg/l

Heavy metals (excl. iron,
cadmium, lead)

< 0.1 mg/l

Chloride

< 2 mg/l

Phosphate

< 0.5 mg/l

Conductivity (at 20°C)

< 15 µs/cm

pH value

5–7

Contaminants/minerals/qualities

Value/Specification

Appearance

colorless, clean, free from sediment

Hardness

< 0.02 mmol/l

Chemical additives

No chemicals or additives must be added to the
water used for the steam sterilization process,
even if they are specifically claimed for use in
steam generators, or for steam production, or
as additives for sterilization, disinfection,
cleaning or corrosion protection.

Notice:
The use of water with a conductivity greater than 15μS/cm (10
ppm) may affect the sterilization process and damage the sterilizer.
The use of water with a conductivity greater than 50μS/cm, or not
complying with the specifications in the table above, may strongly
affect the sterilization process and seriously damage the sterilizer.
The manufacturer’s warranty is void if the sterilizer was used with
water containing contaminant or chemical levels exceeding those
listed in the table above.

«
...
124
125
126
127
128
...
»

Содержание Lisa VA131-17













































































































































Отзывы:

Нет отзывов

Похожие инструкции для Lisa VA131-17

FX-ARM CONTROLLER

Бренд: Magicfx Страницы: 16

Бренд: Datavideo Страницы: 50

Бренд: Waterous Страницы: 90

Бренд: Campbell Страницы: 14

Бренд: ACE INSTRUMENTS Страницы: 2

Бренд: ODA Страницы: 103

Бренд: Garmin Страницы: 12

Бренд: Garmin Страницы: 13

Бренд: Tactile Medical Страницы: 23

Бренд: Taarup Страницы: 72

Бренд: JBM Страницы: 12

HALO miniLUME LA5300

Бренд: Cooper Lighting Страницы: 2

Бренд: Free The Tone Страницы: 8

Бренд: Land Pride Страницы: 72

Бренд: RAB Страницы: 7

Airstream PNEG-362 2000 Series

Бренд: GSi Страницы: 18

Бренд: LIGMAN Страницы: 8

Бренд: Becker-Elektronik Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды