1
10
5
13
13
25
6
3
4
or
1
1
1
13
44
29
44
29
10
14
14
14
14
5
13
13
4
28 x6 27
57
61
62
64
63
58
59
60
17
16
17
38
TRANSFORMER
CABINET
RAIL CAR DOCK WALL (assemble from left to right):
4) Align opening on flange at lower left of first Rail Dock Door Panel (10) with pin
at lower right of first Plain Panel Wall (1) and glue, complete assembly by gluing
a Medium Connector (14) at top as shown.
5) Glue Double Panel Plain Walls (2x 1) together using a Large Connector (13)
as shown. Glue Medium Connectors to top right and left of Plain Walls.
6) Align opening on flange at lower left of second Rail Dock Door Panel (10) with
pin at lower right of right Plain Panel Wall (1) and glue where parts meet. Glue a
Medium Connector to connect the top of both Walls as shown.
7) PLEASE NOTE: Rail Dock Doors (29) can be left off to model an open door:
for a closed door, glue Overhead Door Glass (44) to back of Rail Dock Doors (2x
29). Glue doors in place on back of both Dock Door Panels.
END WALLS
8) PLEASE NOTE: Raised ridges on one edge of Left (5) and Right (4) Corner
Wall Panels as shown are the outside edges. Three styles of Single Panel Walls
are included:
For a plain wall, use part #3, or for an entrance/exit door, use #6 for a right entry
or #7 for left (not shown): drawing shows #6 from the back/inside. Glue Large
Connectors (2x 13) to mounting pins on the plain edge (inside) of both Corner
Walls as shown. Complete assembly by aligning pins on backs of Single Panel
Walls (3, 6 or 7) with openings in large Connectors and gluing where parts meet.
Glue Entry Door (25) to opening in Wall (#6 shown).
BASE SECTIONS
9) The base is designed for easy modification, however some cutting and splicing will be needed for a longer or shorter design. To assemble
as shown, align corner tabs and slots and glue where Long (2x 16) and Short (2x 17) Base Sections meet.
MAIN ASSEMBLY
10) PLEASE NOTE: End Wall assemblies are interchangeable and may be installed at either end. Using raised ridges on lower edges of
completed wall assemblies, carefully align and support walls: glue to Base and at inside corners where parts meet.
EXTERIOR DETAILS
11) Truck Dock - make 6: glue Weather Bellows/Seal (6x 28) to openings as shown. Glue Bumpers (6x 27) to lower edge of seals. If used,
install Canopies (6x 65: not shown) in holes drilled in Step #3.
12) Security Lighting: PLEASE NOTE: If you wish, a light from the Modern Wall Light 3-Pack (#949-4318, sold separately) may be used in
place of the nonworking light fixture (57). Glue lights of your choice to opening in wall as shown.
13) PLEASE NOTE: Parts are included to build two versions of the Large Stairway, select one: Standard: Glue Exterior Panel (62) to outside
edge of Stairs (61). Entrance Ramp: The ramp may be installed on either side (right side shown). Note molded cut lines at left and right on
back of Exterior Panel: carefully remove one end and handrails outside of the straight pipe at the angles of the pipes. Note that the raised
ridge on the underside of Ramp (63) is the upper end; align with top stair and modified Exterior Panel and glue in place. Glue Ramp Exterior
(64) to outside edge. Both versions: align completed steps with large entry doors and glue to walls where parts meet.
14) Glue Large Handrail (59) to mounting points in top of Small
Stairway (58). Glue End Railing (60) as shown in mounting point and
on inside edge of Large Handrail. Align completed steps with small
entry door and glue to wall where parts meet.
15) Rail Dock - make 2: align pins on back of Weather Bellows/Seal
Base (2x 31) into notches on edges of Dock Door Panel (10) and glue
in place. Glue Exterior Bellows/Seals (2x 30) to outside of Base.
46
7
or
