background image

Rev. 1.5

 

Operating Manual Table-top Greasing Device TBV-H-0x-xx 

Page 14 of 35 

 

 

 

Walther Systemtechnik GmbH 

 D 76726 Germersheim 

Telefon: +49 (0)7274-7022-0 Telefax: +49 (0)7274-7022-91 
http://www.walther-2000.de 

 [email protected] 

 

7  Taking out of Service  

For short interruptions, such as overnight or during weekends switch off main switch. Pressure inside 
equipment is removed and electrical power off (check displays). 

 

 

NOTE 

Please follow the maintenance instructions! 

 

7.1  Long-term Interruption  

Please observe procedure stated below when taking equipment out of service for longer periods: 

 

Switch off main switch. 

 

Disconnect mains plug. 

 

Pressure inside equipment must be removed (check displays). 

 

 

NOTE 

Please follow the maintenance instructions! 

 

7.2  Shutdown of Device  

Please observe the following procedure, when finally shutting down the device: 

 

Switch off main switch. 

 

Disconnect mains plug. 

 

Pressure inside equipment must be removed (check displays). 

 

Drain grease or oil and take care of proper disposal. 

 

 

WARNING 

Danger of accidents und environmental hazard: Do not spill grease or oil. 
Ensure proper disposal of grease and oil (hazardous waste).

 

 

NOTE 

Please follow the maintenance instructions!

 

 

Содержание TBV-H-01




































Отзывы: