OVERVIEW
The LDS-700 is a dual technology line voltage wall switch
sensor in the IR-TEC’s WALLSENZR family designed to fit
in a standard NEMA wall box for energy efficient automatic
load control. This state-of-the-art wall switch sensor
combines digital Passive Infrared (PIR) and advanced High
Frequency Doppler (HFD) sensing technologies into an
aesthetically pleasing housing to provide second-to-none
occupancy/vacancy sensing performance within its 180°
field of view detection range.
The sensor is factory set to turn ON the load automatically
when PIR sensor detects the presence of an occupant,
and will turn OFF automatically if no motion is detected by
either PIR or HFD sensor before the delay time elapses. To
comply with specific energy code, such as CA Title 24, the
LDS-700 series can be easily programmed to operate as a
Vacancy Sensor. In vacancy sensing mode, the sensor will
only turn ON the load by pressing the push-button
manually and will turn OFF the load automatically as per
sensor delay time set. Various sensing operation and
control modes can be achieved by different DIP switch
setting combinations and push-button operations.
INSTALLATION NOTES
SPECIFICATIONS
Line Voltage Dual-Tech Wall Switch Sensor
INSTALLATION INSTRUCTIONS
LDS-700 Series
Power supply
Sensing technology
Inrush current
Load switching
Detectable speed
Mounting height
Ambient light level
Delay time setting
Op. humidity
Op. temperature
Dimensions
Detection coverage
Maximum load
120/277VAC, 60Hz
Digital PIR & High Frequency Doppler
Incandescent/Halogen – 800W (VA)
Fluorescent Ballast/CFL – 800W (VA)
Ballast Electronic (LED) – 500/800VA@120/277V
Motor – 1/6 HP
Max. 80A, 16.7 ms @60Hz
Zero-cross Hybrid-Switching
1~10 ft./sec. (0.3~3 m/sec)
3~5 ft. (90~150 cm) above the floor
Major motion - 30 ft x 40 ft (W x L) @4 ft high
Minor motion - 20 ft x 20 ft (W x L) @4 ft high
7 levels, from dark to 24 Hour
T/1’/3’/5’/10’/20’/30’, T=10 sec. for testing
Max. 95% RH, non-condensate
-40°F ~ 131°F (-40°C ~ 55°C)
4.13”H x 1.77”W x 1.65”D (w/mounting plate)
INDOOR USE ONLY
Utilisation a L'interieur Uniquement
Risk of Electric Shock - Disconnect power supply at the circuit breaker
before installing, replacing lamps, or servicing.
DO NOT
control a load in excess of specified ratings to avoid damaging the
sensor or the property.
Install and use this sensor in accordance with electrical codes and regulations.
This device is intended to be installed by a qualified electrician.
DO NOT
attempt to service or repair.
Afin d'eviter tout risque de choc electrique ou electrocution, couper le
courant au disjoncteur avant installation, remplacement des lampes ou
tout service d'entretien.
NE PAS contrôler une charge supérieure à la capacité spécifiée pour éviter
d'endommager le capteur ou la propriété.
Installer et utiliser ce capteur conformément aux codes et règlements
électriques.
Ce dispositif est destiné à être installé par un électricien qualifié. NE PAS
tenter de réparer.
The sensor is more sensitive to the movements
“crossing” the detection zones than “toward” or “away”
the sensor. To obtain better sensitivity, ensure the sensor
to have clear field of view for the occupant’s motion
within the desired coverage.
The closer movement is to the sensor, the more
sensitive the sensor is.
The sensor should be mounted within the specified
mounting height for optimal performance.
Avoid blocking the sensor with any obstacles, such as
door, plant, partition or furniture. As a general rule, every
occupant within the desired range should be able to
clearly see the sensor.
Do NOT mount the sensor directly above or nearby a
heat source, or where unintended motion (e.g. hallway
traffic) will be “seen” by the sensor.
1.
2.
3.
4.
5.
DETECTION COVERAGE
40’
Top view
Side view
4’
7’
30’
40’
Minor motion
20’
20’
Major motion
180°, 30 ft x 40 ft (W x L)
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1)This device may not cause harmful interference,
(2)This device must accept any interference received,
Including interference that may cause undesired operation.
FCC NOTICE
P/N: 058-70004-003
Printed in Taiwan
www.irtec.com
This product may be covered by one or more U.S. patents or patent applications.
Please visit www.irtec.com for more information.
WARNING & CAUTION
AVERTISSEMENT & PRUDENCE
Install the sensor at least 1ft. away from any occupant.
