background image

2

P202

Safety

Safety Alert Symbol

This Safety Alert Symbol means: 

ATTENTION! BE ALERT! 
YOUR SAFETY IS INVOLVED!

The 

Safety Alert Symbol

 identifies important safety messages 

on the machine and in this instruction. This symbol means 
be alert to the possibility of personal injury or death. Follow 
instructions provided.

Signal Words

The signal words 

DANGER

WARNING

 and 

CAUTION

 determine 

the seriousness level of the warning messages in this manual. 
The appropriate signal word for each message in this manual 
has been selected using the following guidelines:

DANGER –

Indicates an imminently hazardous situation that, if not avoided, 

will

 result in death or serious injury. This signal word is to be 

limited to the most extreme situations typically for machine 
components which, for functional purposes, cannot be guarded.

WARNING –

Indicates a potentially hazardous situation that, if not avoided, 

could

 result in death or serious injury, and includes hazards that 

are exposed when guards are removed. It may also be used to 
alert against unsafe practices.

CAUTION –

Indicates a potentially hazardous situation that, if not avoided, 

may

 result in minor or moderate injury. It may also be used to 

alert against unsafe practices.

IMPORTANT

 – To avoid confusing equipment protection with 

personal safety messages, a signal word IMPORTANT indicates 
a situation that if not avoided, could result in damage to the 
machine.

Equipment Operation

 WARNING!

Avoid the risk of personal injury or machine 

damage! Read the operator’s manual before 

using this equipment. Carefully read all safety 

messages in the manual and follow all safety 

signs on the machine.

 CAUTION!

Review your chain saw manual for safe operating 

and handling procedures before beginning work.

 WARNING!

Do not attach a chain saw to the holder with a bar 

length longer than 30" (75 cm). The cutting chain 

could contact the push block or cylinder rod 

causing a hazardous situation. Injury or machine 

damage could result from flying debris.

Содержание P202











Отзывы: