background image

•  Do not operate winch until you have read and understood operating 

instructions in Operators Manual.

•  Never allow children or anyone incompetent to operate the winch.

•  Keep hands, feet, clothing, and hair away from moving parts. 

•  Keep children, pets, and bystanders away from area of operation.  

•  Never operate winch without checking that all workers are away from 

machinery and cables in a safe area.

•  Check for loose pins, bolts, and shields before each operation.  

Tighten or repair as required.  Ensure winch is properly attached to 

tractor.

•  Wear safety boots and protective clothing as well as eye and ear 

protection.  Always wear heavy gloves suitable for handling the steel 

cable.

•  Check cable condition before using the winch.  Never operate the 

winch if the cable is corroded, knotted, or has broken strands or 

sharp kinks.  Operating with faulty cable could cause the cable to 

break and fatally injure the operator.

•  Stand at least 8 feet to the side of the winch to pull control rope while 

operating winch.  Do not operate winch from tractor seat unless 

protective shield is in place.

•  Never stand directly in line with cable while pulling.  

•  Operator incompetency can be fatal!  Do not operate machine when 

tired or under the influence of alcohol, drugs, medication or other 

substance.

•  Park tractor and winch on a level location for winching.  Always lower 

winch blade to ground when winching to anchor the tractor.

•  Always winch with cable in line with machine.  Do not exceed a 

winching angle of more than 25 degrees.  Always winch up a slope—

to avoid tractor rollover never winch across a slope.

•  Never handle cable while winch is in operation.  

•  Before servicing winch, disengage PTO, stop tractor, and remove 

key to prevent accidental start up.

•  Keep cable as short as possible when towing logs.  To prevent 

tractor roll over, use only a tractor with an approved ROPS with 

an appropriate counter weight on the front.  Keep winch as low to 

ground as possible.

•  This winch is designed for winching and skidding only.  Never 

attempt to use it as a hoist or for lifting purposes.

Содержание FX12000





















Отзывы: