Wallenstein 1102R215 Скачать руководство пользователя страница 14

Страница: 14 / 72

Safety

BX52R, BX72R, BX102R

3 PH Roller-feed Chipper

Safety

10. WARNING!

Risk of personal injury. Operate chipper
at the correct PTO speed and direction.

Tractor PTO must operate at 540 or 1000
rpm, rotating in the direction of the arrow.

11. WARNING!

Risk of personal injury!

Stop the machine and disconnect the
PTO shaft before performing any repair
or maintenance procedure. Place the
machine in a state that makes it safe to
work on. See

Safe Condition on page

2.13 Replacing Damaged Safety Signs

•

Keep safety signs clean and legible at all times.

•

Replace safety signs that are missing or have become
illegible.

•

Parts that were replaced with a safety decal on them must
also have the safety sign replaced.

•

Replacement safety signs are available from your
authorized Distributor, Dealer Parts Department, or
Wallenstein Equipment.

Procedure

Be sure that the installation area is clean and dry.

Be sure temperature is above 50 °F (10 °C).

Determine exact position before removing from the backing
paper.

Pull the decal off the backing sheet, align the sign over
the specified area, then carefully press the exposed sticky
backing in place.

Use a piece of the backing paper to smooth the decal out,
pressing from the center outwards.

Small air pockets can be pierced with a pin and smoothed
out using the piece of sign backing paper.

Содержание 1102R215









































































Результаты поиска

Содержание 1102R215

Отзывы:

Похожие инструкции для 1102R215

Бренды по названию

Популярные бренды

Wallenstein 1102R215, Руководство оператора

Результаты поиска

Содержание 1102R215

Отзывы:

Похожие инструкции для 1102R215

Бренды по названию

Популярные бренды