background image

WALLAS 40D

 

Operator’s Manual and Installation Guide

 

 

13

 
 
 

Figure 16 

 
 

Figure 17 

 
 

Figure 18 

Fuel Lines & Filters

 

 
Wallas diesel products come with 
polyethylene fuel line kits shipped in the 
carton, which include a fuel filter & 
miscellaneous adapters.   
 
If you purchase a Wallas day tank, these 
fuel line kits are not used, being replaced 
by a complete #367215 tank adapter kit.  
The #367215 kit has it’s own tank end filter.  
Only one filter should be used. 
 
The fuel lines are attached to the furnace 
using a three part compression fitting, 
shown in the images to the right.  Correct 
first assembly of the fuel line fitting and 
mounting to the Wallas appliance is very 
important. 
 

1.

 

Make sure the fuel line end is cut 
cleanly and squarely. 

2.

 

Slide the nut on the fuel line, with 
the threads toward the line end. 

3.

 

Push the acorn over the end of 
the fuel line. 

4.

 

Slide the ferrule into the end of 
the fuel line until the flange sits 
snugly against the plastic tube. 

5.

 

Check the fuel fitting on the 
Wallas product and the 
acorn/ferrule end, making sure 
they are clean and free of debris. 

6.

 

Place the end of the acorn 
against the Wallas product’s fuel 
fitting and slide the nut against 
the threads. 

7.

 

Spin the nut onto the threads and 
tighten very firmly.  This process 
compresses the fitting. 

8.

 

Loosen the nut and re-tighten for 
a fully sealed fit. 

 

Please note:  ABYC and NMMA rules 
may require the use of fire rated fuel 
lines in new vessel applications.  Please 
contact Scan Marine for these products 
and their correct application. 

Содержание Nautic 40D

















Отзывы: