wallas 30 GB Скачать руководство пользователя страница 37

Страница: 37 / 38

Maintenance

Troubleshooting, indicating flameout / overheat

The overheating thermostat has

activated and stopped the function

of the fuel pump.

Check that the device is not in after

cooling mode. After cooling mode

uses the same signal and it’s not

malfunction but a normal procedure.
(If it is a malfunction, after 5 minutes

the red signal (1) flashes in 30

seconds interval).

Check that the main blower is

rotating.

Check that the adjustment

flaps of the warm air grills are

open.

Check the amount of

ventilation air.

Check the condition of the

warm air ducts (pressed,

blocked).

After the after cooling

procedure, start again.

Yes

Red

Indicating flameout

The malfunction continues

after the restart of the device.

The fuel has run out or its level is

too low for the intake hose in the

tank to reach it.

High wind pressure at the exhaust

lead-through fitting.

Water in the exhaust gas hose.

Water in the fuel.

The burner is sooted.

The fuel pump is broken.

The fuel needle is blocked.

Add fuel.

Ensure that the wind does not blow

directly in the lead-through.

Check the bends and loops of the

flue gas hose for water

(water trap).

Dewater the fuel or replace it.

4.3.3_en

Bring the device in for service.

FAULT INDICATION WITH

BLINKING LIGHTS

Red

Overheat

Yellow

FAULT INDICATION WITH

BLINKING LIGHTS

D20061

- 91 -

22 GB / 30 GB

490529

Содержание 30 GB







































Результаты поиска

Содержание 30 GB

Отзывы:

Похожие инструкции для 30 GB

Бренды по названию

Популярные бренды

wallas 30 GB, Руководство пользователя

Результаты поиска

Содержание 30 GB

Отзывы:

Похожие инструкции для 30 GB

Бренды по названию

Популярные бренды