Wallace Perimeter Security ALPHA Скачать руководство пользователя

Страница: 29 / 182

Alpha/Delta (Kinetic Operator) Installation and Maintenance Manual

Revision 1 - MAY 2023

UL 325 COMPLIANT SENSORS

All external entrapment protection

sensors

must have NC sensor output

and be wired to the SENSOR COM

terminal for monitoring and powering

purposes. Depending on software

version, the sensor becomes powered

when the gate operator’s motor

runs or is always powered when the

operator is connected to AC power.

UL 325 Compliant Sensors

The following sensors have been tested with Nice | HySecurity gate operators by an independent

laboratory and certified to comply with UL 325 7th Edition. Select sensors from this list for UL compliant

gate automation solutions. Contact the sensor manufacturer for specific recommendations for use.

Recommended External Entrapment Protection Sensors List for the SmartDC Controller – Kinetic Operator

Mfg. Part # or Model

Brand

Wallace Perimeter

Security Part #

Max. Range

Photo Eyes

(Retro-reflective)

E3K-R10K4-NR-1

Omron

40 ft (12.2m)

NIR-50-325

EMX

45 ft (13.7m)

IRB-RET

EMX

53 ft (16.1m)

E-931-S50RRGQ

Seco-Larm

46 ft (14m)

Photo Eyes

(Thru-Beam)

OVS-50TNR

Optex

33 ft (10m)

IRB-MON

EMX

100620

65 ft (19.8m)

E-960-D90GQ

Seco-Larm

90 ft (27.4m)

Edge Sensors

Sentir Series

ASO Safety

100543

CPT210-2U-#-T2

Miller Edge

Edge Sensor

Converters

Hy2NC (Converts 10K to

NC Monitoring)

HySecurity

Multi-Input Module

The Solution – MIM-62

Miller Edge

Содержание ALPHA























































































































































































Результаты поиска

Содержание ALPHA

Отзывы:

Похожие инструкции для ALPHA

Бренды по названию

Популярные бренды

Wallace Perimeter Security ALPHA, Руководство по установке и обслуживанию

Результаты поиска

Содержание ALPHA

Отзывы:

Похожие инструкции для ALPHA

Бренды по названию

Популярные бренды