Alpha/Delta (Kinetic Operator) Installation and Maintenance Manual
Revision 1 - MAY 2023
25
EXTERNAL ENTRAPMENT PROTECTION SENSORS
External Entrapment Protection Sensors
Kinetic is equipped with a Type A inherent entrapment sensor (IES). UL 325 Safety Standard compliance
requires installation of external entrapment protection sensors, the number of which, depends on the
entrapment hazards that exist at each particular installation.
To comply with UL 325, the following external sensors may be used:
•
Contact sensors, such as edge sensors
• Non
-
contact sensors, such as photoelectric eyes
The site designer or installer can choose either photoelectric eyes or edge sensors or use these devices in
combination. Whatever devices are used, protection in both the opening and closing directions of gate
travel must be provided.
The UL 325 Safety Standard for automatic sliding gates specifically requires that edge sensors or
photoelectric eyes or a combination of both devices be installed to protect against pedestrian entrapment
in BOTH directions of the gate travel and where an entrapment hazard exists.
PHOTOELECTRIC EYES:
One or more photoelectric eyes shall be located where the risk of entrapment or
obstruction exists, such as the perimeter reachable by a moving gate.
A photoelectric eye or contact
sensor is also required to protect
against possible entrapment if the
gate opens to a position less than
16 inches (40.6cm) from any object,
such as a post or wall.
EDGE SENSORS:
One or more edge sensors shall be located on the leading and trailing edges of a slide
gate where the risk of entrapment or obstruction exists. One or more contact sensors (edge sensors) shall
be located at the leading edge, trailing edge, and post-mounted, both inside and outside of a sliding gate.
SENSOR SECURITY:
A hard -wired sensor shall be located and its wiring arranged so that communication
between the sensor and gate is not subjected to mechanical damage.
SENSOR FUNCTION and COMMUNICATION:
A sensor that transmits its signal to the gate operator must
be located so its signal is not impeded by building structures or other obstructions. All sensors must be
installed so that they function as intended for the end-use conditions.
Содержание ALPHA
