Wallace Perimeter Security ALPHA Скачать руководство пользователя

Страница: 145 / 182

Alpha/Delta (Kinetic Operator) Installation and Maintenance Manual

Revision 1 - MAY 2023

145

INSTALLING PHOTOELECTRIC SENSORS FOR EXTERNAL ENTRAPMENT PROTECTION ONLY

Installing Photoelectric Sensors for External Entrapment

Protection Only

Refer to Figure 42 to help plan the most appropriate placement for the photo eyes being installed as

external entrapment protection devices. If no other external entrapment protection devices (like edge

sensors) are installed, then at least two photoelectric sensors are required to guard the gate in each

direction of travel. If the photo eyes are tripped, the operator will temporarily stop the gate.

Consult a photoelectric sensor manual for wiring details. Make all electrical connections to SmartDC

Controller as shown in Figure 43 on the next page.

Operation Notes

• A photo eye trip does not reverse gate.
•

The SmartDC Controller software is factory set to stop upon photo eye trip.

•

Software is configurable to stop and reverse two seconds upon photo eye trip.

If the photo eye is cleared within five seconds, the gate will proceed in the direction of travel.

The SmartDC Controller has three sensor inputs (Sensor 1, Sensor 2, Sensor 3) which can be used for any

type of photoelectric inputs. See

“Figure 43. Connections for Entrapment Protection Only” on page

146

. Underwriters Laboratories requires that any non-contact sensor used as an external entrapment

protection device, must be tested to, and recognized by, the UL 325 Standard.

There are two common types of photoelectric sensors, thru-beam and retro-reflective, and each has its

advantages.

Figure 42. Photoeye Placement as External Entrapment Protection Devices

Содержание ALPHA























































































































































































Результаты поиска

Содержание ALPHA

Отзывы:

Похожие инструкции для ALPHA

Бренды по названию

Популярные бренды

Wallace Perimeter Security ALPHA, Руководство по установке и обслуживанию

Результаты поиска

Содержание ALPHA

Отзывы:

Похожие инструкции для ALPHA

Бренды по названию

Популярные бренды