Walker T23 Скачать руководство пользователя страница 53

Страница: 53 / 96

Operating Instructions

Power Dump Option

When equipped with the optional power dump sys-

tem, the operator dumps the catcher while sitting in

the seat. A toggle switch operating a power ram is

used to raise and lower the catcher. The back door

automatically opens and closes during the dump

cycle.

Hold the toggle switch

DOWN

RAISE

LOWER

the catcher. When the catcher reaches the

full raised or lowered position, the power ram clutch

will make a ratcheting sound. Release the toggle

switch as soon as this sound is heard.

DO NOT

operate the ram with the clutch ratcheting for an

extended time

as this will cause extra wear on the

clutch mechanism.

CAUTION

The operator should be in the seat and by-

standers stay clear when the power dump

is operating. The power dump is used

ONLY for tailgate dumping. Do not attempt

to use the optional dump bag or any other

bag with the power dump.

NOTE:

If grass tends to hang up in the catcher

after raising the catcher with the power dump, “jig-

gle” the steering levers and make the tractor bounce

a little to unstick the grass and make it slide out of

the catcher.

NOTE:

With the power dump mechanism in the

normal operating position (catcher down), the catch-

er can be

manually raised

for access to the engine

and the catcher can be

manually dumped.

Hi-Dump

Option

When equipped with the optional Hi-Dump

system,

the operator raises and dumps the catcher while sit-

ting in the seat. Two toggle switches operate inde-

pendent hydraulic cylinders to raise and lower the

catcher. The back door automatically opens and

closes during the dump cycle.

NOTE:

The ignition switch must be in the

ON (RUN)

position for the Hi-Dump

system to operate.

Toggle Switch

(Lift)

Toggle Switch

(Dump)

(+) Auxiliary

Power Terminal

(-) Auxiliary

Power Terminal

Lift/Dump Control Switches and

Auxiliary Power Terminals

Hold the Lift toggle switch

DOWN

RAISE

LOWER

the catcher. Hold the Dump toggle

switch

DUMP

the catcher and

DOWN

to return

to the normal operating position. The catcher may

be dumped at any raised position (Normal Operat-

ing - Intermediate - Fully Raised).

Содержание T23

































































































Результаты поиска

Содержание T23

Отзывы:

Похожие инструкции для T23

Бренды по названию

Популярные бренды

Walker T23, Руководство оператора

Результаты поиска

Содержание T23

Отзывы:

Похожие инструкции для T23

Бренды по названию

Популярные бренды