Walker S14i Скачать руководство пользователя страница 33

Страница: 33 / 88

Operating Instructions

Parking Brake

The parking brake functions by locking a detent arm

to a cog in the hydraulic motor rotor. Moving the

lever

FORWARD engages

the parking brake; mov

ing the lever

BACKWARD releases

the brake.

IMPORTANT:

Stop the tractor completely before

engaging the parking brake. The parking brake

uses a positive mechanical lock similar to the

PARK

position on an automotive automatic transmission.

If the tractor is moving when the brake is engaged,

it will result in sudden stoppage and possible inter

nal damage to the transaxle.

NOTE:

If pressure on the parking brake (e.g.,

parked on a hill) makes it impossible to release the

parking brake with the parking brake lever, move the

mower gently forward or backward to allow the

brake detent to release.

Engaged

Position

Parking Brake Engaged

Disengaged

Position

Parking Brake Disengaged

Transaxle Lockout Arms

The transaxle lockout arms disengage the transax

les. By

lifting

the arms up and locking them into

place with the shoulder on the arm in the chassis

notch, the transaxles are released to permit free

wheeling. By releasing the arms and

recessing

them back toward the chassis, the transaxles are

engaged for normal operation. The transaxle arms

in the

LOCKOUT

position are used to enable mov

ing the machine without the engine running (e.g., for

service). Refer to

TRANSAXLE LOCKOUT

in this

section for operating instructions.

Transaxle

Lockout Arms

Transaxle Lockout Arm Location

NOTE:

The transaxle lockout arms ends should be

completely retracted against the chassis, otherwise

operation of the transaxle may be erratic.

Engine Service Light

The engine service light indicates that the engine

Electronic Control Unit (ECU) has detected a fault in

the engine performance. When this light illuminates

during operation, contact an authorized Kohler Ser

vice dealer to diagnose the fault.

IMPORTANT:

Continued operation of the engine

with an illuminated engine service light will result in

sub-standard performance and

MAY

cause engine

damage if not corrected as soon as possible.

Содержание S14i

























































































Результаты поиска

Содержание S14i

Отзывы:

Похожие инструкции для S14i

Бренды по названию

Популярные бренды

Walker S14i, Руководство оператора

Результаты поиска

Содержание S14i

Отзывы:

Похожие инструкции для S14i

Бренды по названию

Популярные бренды