manualshive.com logo in svg

Walker MT, MTL, MTEFI, MTLEFI, Подробные инструкции, Страница: 38 / 256

Поделиться
Скачать
Walker MT, MTL, MTEFI, MTLEFI Скачать руководство пользователя страница 38

Page: 1-18

WALKER MANUFACTURING COMPANY

July 2006

SERVICE INSTRUCTIONS

Implement Hitch Wiring

1.

Drill five (5) 13/64 in. (5 mm) diameter holes in the
tractor, two in the FSC lever and three in the body,
as shown in the illustration.

Drill Holes for Implement Hitch Wiring

2.

Attach the toggle switch mounting bracket on the
FSC lever using two (2) 10-24 x 1/2 in. bolts and
Keps nuts.

Attach Toggle Switch Mounting Bracket

3.

Install the wiring harness to the tractor body using
the three wiring clamps, three 10-24 x 3/8 in. bolts
and Keps nuts.

4.

Attach the toggle switch to the mounting bracket,
placing the switch terminals toward the 

front

 of the

mower.

Attach Wiring Harness and Toggle Switch

5.

On Models MC, MDD/MDG, and MT, connect the
harness red wire to the load side of the circuit
breaker mounted on the bracket behind the bat-
tery.  Connect the green ground wire to the chassis
ground bolt.

Connect Harness Wire to Circuit Breaker

IMPORTANT:

For all 1987-1997 Model MC trac-

tors (with Kohler Magnum engine), connect the har-
ness red wire to the free connector of the PTO
clutch switch red wire.  Refer to 

Implement Hitch

Wiring Diagram

 illustration.

Wiring

Harness

Mounting

Bracket

Ground

Wire

Mounting Bracket

Harness

Switch

Terminals

Wiring Clamps

Red Wire

Circuit Breaker

Содержание MT, MTL, MTEFI, MTLEFI

































































































































































































































































Отзывы:

Нет отзывов