background image

Safety Instructions - Operating

11

  WARNING

If Equipped With ROPS:

 

 

Always keep the ROPS roll bar in the up-

right and locked position when operat-

ing.

 

 

Always use the seat belt when the roll 

bar is upright.

 

 

Only lower the roll bar when absolutely 

necessary for overhead clearance.

 

 

Never use the seat belt when the roll bar 

is lowered.

1.  

Operate the mower only in daylight

 or in 

good artificial light with good visibility of the area 

being mowed.

2.   Sit  on  the  seat  when  starting  the  engine  and 

op

erating the machine.  Keep feet on the deck 

footrests at all times when the tractor is moving 

and/or mower blades are operating.  

Never op-

erate the tractor without a deck or imple-

ment installed.

3.   For a beginning operator, 

learn to steer (ma-

neuver) the tractor with a slow engine speed 

before attempting any mowing oper ation.  

Be aware that, with the front mounted mower 

configuration, the back of the tractor swings to 

the outside during turns.

  DANGER

Do not mow around overhanging tree 

branches or bushes at the same height as 

the operator’s torso and head where inad-

vertent contact may cause injury.

4.   Remember, for an emergency stop, the forward 

motion of the tractor can always be stopped by 

pulling the Forward Speed Control (FSC) into 

the 

NEUTRAL-PARK 

position.

5.   In case the transmission drive belt breaks dur­

ing operation, and if the machine is on a slope, 

the machine will freewheel down the slope.  

To 

maintain control,

 immediately (1) Release the 

steering  levers  and  simultaneously  (2)  Move 

the  FSC  to  the 

NEUTRAL-PARK

  position.  

When the machine is stopped or moving slowly, 

engage the parking brake.

NOTE:  

The emergency stop procedure is ex­

actly the same procedure as used to normally 

stop and park this machine.

6.   Disengage the blade clutch, put the FSC in the 

NEUTRAL-PARK

  position,  and  engage  the 

Parking  Brake  before  starting  the  engine  (an 

 

ignition  interlock  switch  normally  prevents 

 

starting of the machine if these controls are in 

the 

OPERATING

 position).

7. 

Do not operate machine if the operator pres-

ence safety switch system is not working.

  

Verify proper operation by having the operator 

lift off the seat with the engine running and mov­

ing three controls, one at a time; (1) Move the 

FSC lever out of the 

NEUTRAL-PARK

 position, 

(2) Engage the PTO Clutch, and (3) Disengage 

the  Parking  Brake.    Moving  any  of  these

 

controls should stop the engine after a 1/2 sec­

ond delay.

8.  

Do  not  run  the  engine  in  a  confined  area 

without adequate ventilation.  

Exhaust fumes 

are hazardous and can be deadly.

9.  

Do not carry passengers

 ­ maximum seating 

capacity is one (1) person.

10.  Watch for holes, rocks, and roots in the terrain 

and for other hidden hazards.  When mowing 

tall grass, mow higher than desired to expose 

any hidden obstacles.  Then, clean the area and 

mow to the desired height.

11.  

Avoid sudden starts or stops.  

Before back­

ing 

the machine up, look to the rear to be sure 

no one is behind the machine.  Watch carefully 

for traffic when crossing or working near road­

ways.

Содержание H27i





















































































Отзывы: